Changing the Sound of a Patch (Edit Mode)
ZOOM GFX-5
18
5.
To change the effect type for the selected
module, turn the [VALUE] dial.
6.
To change a parameter value, press one
of the PARAMETER [
Q
]/[
W
] keys.
When you press the key, the parameters of the
currently selected effect type are called up on the
display one by one. The [GROUP/BANK] indicator
shows the parameter value.
7.
Turn the [VALUE] dial to change the
parameter value.
For some modules such as DRIVE and
EQUALIZER, effect types and parameters can be
changed directly with the knobs and keys on the
panel.
8.
Repeat steps 3 - 7 to edit other modules.
9.
When editing is completed, press the
[EDIT/EXIT] key.
The unit returns to the play mode. If any element of
the patch has been changed, the “EDITED” dot is
shown on the [GROUP/BANK] indicator.
NOTE
If you wish to keep the patch, be sure to perform
the store operation (
→
p. 19) . Otherwise all
changes will be permanently lost as soon as you
switch to another patch.
Changing a patch name
If you wish, you can assign a new name to an edited
patch. Proceed as follows.
1.
In edit mode, press the [TOTAL] key.
2.
Use the PARAMETER [
Q
]/[
W
] keys to
bring up the patch name on the display.
The flashing character is the one that can be
changed.
3.
Use the PARAMETER [
Q
]/[
W
] keys to
select the character, and turn the [VALUE]
dial to change the character.
Available characters are listed on page 34.
4.
Repeat step 3 until the name is as desired.
Then press the [EDIT/EXIT] key to return
to the play mode.
Do not forget to store the patch (
→
p. 19) to retain
the edited name.
-OFF-
HALL
TIME
20
When a dot is shown here, the patch was edited.
If you return the parameter to the original value,
the dot will disappear.
Character
to change
POWER
ZOOM GFX-5
19
Storing and Swapping Patches
This section describes how to store an edited patch in memory, and how to swap patches in a user group.
1.
In play mode, manual mode, or edit mode,
press the [STORE] key.
The GFX-5 enters the store standby condition. The
patch name and the indications “STORE” or
“SWAP” are shown alternately on the display.
The [GROUP/BANK] indicator shows the current
group and bank number, and the LED of the
respective foot switch lights up.
H
INT
To change the name of a patch before storing,
see page 18.
2.
Turn the [VALUE] dial to select either
“STORE” or “SWAP”.
When “STORE” is selected, you can save the
current patch in any user group patch slot.
When “SWAP” is selected, you can exchange the
current user group patch with any other user group
patch. This is convenient for example if you want to
change the order of patches for use during a
performance.
N
OTE
If the original patch is from a preset group, the
“SWAP” option is not displayed.
3.
Use the PARAMETER [
Q
]/[
W
] keys and
the BANK [
Q
]/[
W
] foot switches to select
the group and bank for the store/swap
target.
4.
Use the foot switches [1] - [3] to select the
patch number of the store/swap target.
The LED of the respective foot switch lights up.
N
OTE
A preset group cannot be selected as store
target. If you press the [STORE] key while a patch
from a preset group is selected, the patch
number 1 of "U0" (user group) will be
automatically selected as the default store
target.
5.
Press the [STORE] key once more.
The store or swap operation is performed and the
unit returns to the original mode. If the patch in step
1 was being edited, the editing changes are stored
and the “EDITED” dot disappears.
If you press the [EDIT/EXIT] key instead of the
[STORE] key, the store/swap operation is canceled
and the unit returns to the original mode.
STORE?
Lit
Patch
Patch
Patch
Bank 8
Patch
Patch
Patch
Bank 1
Currently selected
patch
Patch specified as
swap destination
Swap
