Zontes ZT310T-M Скачать руководство пользователя страница 33

Страница: 33 / 184

33 / 184

shown in the figure. The bolt here cannot be removed
temporarily, just loosen it completely.

b. Use 4# inner hexagon to remove the 3 M6×16 bolts

+ flange b flange bushing cushioning glue as
shown in the figure.

c. Remove the air inlet cover and the air inlet filter

element together. Remove the rubber strip on the box.

4. Replace the air inlet filter

a. Remove the old air inlet filter element and the

rubber strip on the air inlet cover. Use a blow gun to
blow away the dust on the inside, then wipe the inner
wall dry with a clean non-woven fabric.

b. Replace with 2 new rubber strips (one is installed in

the air inlet cover, the other is installed in the box). Take
out the new air inlet filter element and install it into the

air inlet cover in the direction shown.

5. Remove the air filter housing

a. Use a Phillips screwdriver to remove the 9 screws

that fix the housing of the air filter.

b. Remove the air filter housing.

6. Replace Air filter element

a. Use a Phillips screwdriver to remove the 6 screws

that fix the filter element that comes with the air filter.

b. Remove the old air filter element. Blow the dust

inside the air inlet pipe with a dust blower, and then wipe
the inner wall with a clean non-woven cloth.

Содержание ZT310T-M

























































































































































































Результаты поиска

Содержание ZT310T-M

Отзывы:

Похожие инструкции для ZT310T-M

Бренды по названию

Популярные бренды

Zontes ZT310T-M, Руководство по обслуживанию

Результаты поиска

Содержание ZT310T-M

Отзывы:

Похожие инструкции для ZT310T-M

Бренды по названию

Популярные бренды