ZOJE ZJ781-BD Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 24

ZOJE ZJ781-BD Скачать руководство пользователя страница 20

under 93 stitches

10~12mm

between 93-123

5mm

More than 123 stitches

0

The phenomenon when the adjustment value changes:

Moving the low-speed bumps counterclockwise can reduce the number of stitches from low
speed to stop.

25. Starting lever and starting ram position

Adjustment method:

When the machine is stopped, the gap between the end of the adjusting screw on the starting ram
and the stop frame is 0.5~1mm; the gap between the starting lever and the convex surface of the
fuselage base is 3mm.

The phenomenon when the adjustment value changes:

If the gap at the starting ram is too large, it cannot be rotated at a high speed. If it is small, it will
cause an inaccurate stop.

26. Belt adjustment

Head start fork position

：

Adjustment method:

When idling, the belt is exposed from the runner by about 0.5~1mm, which is adjusted by the
long hole of the starting fork (on the nose). At low speed, the belt should completely cover the
drive pulley.
Note: When idling, try not to make the belt contact the starter fork (on the handpiece).

The phenomenon when the adjustment value changes:

When idling, if the belt is wrapped around the drive pulley, the belt will be easily worn and the
pulley will heat up.

Speeding mechanism fork position

Adjustment method:

«
...
18
19
20
21
22
...
»

Содержание ZJ781-BD

























Отзывы:

Нет отзывов