background image

2.

 

Lay the patch in position on top of the area to be patched and draw around it with a 
pencil. This marks the area to be glued.  

3.

 

Clean the patch and the area to be repaired with MEK. This not only cleans the area but 
prepares the material so the glue will penetrate and hold better. For PVC it is not 
necessary to do any buffing.  

4.

 

Mix glue and accelerator in your bowl or cup in correct proportion, mixing only as much 
as you will need for this repair. We have found estimated proportions work just fine. A 
more precise measure is 120 drops per 8 ounce cup.  

5.

 

Using the cut off paint brush, apply the first coat of glue to both pieces that are being 
joined. Let the glue dry thoroughly between coats -- approximately 15 minutes or until it 
is not tacky.  

6.

 

Repeat the same procedure for the second coat of glue.  

7.

 

When thoroughly dry, apply the patch in the correct position, pressing from the center 
outward to eliminate air bubbles.  

8.

 

Using a small roller or the rounded end of a screw driver, press firmly on the patch in all 
directions. At the same time, apply heat as this is very important to re-activate the glue. A 
hair dryer on high works well. It is not recommended for someone without experience to 
use a heat gun as it can easily get too hot for the material.  

9.

 

Allow the glue to cure (with the boat inflated) for 24 hours before use on the water. 

 
Zoik Inflatable Warranty 

What your Warranty DOES Cover: 

 

The 2, 3, and 5 year warranties cover all retail purchases on all Zoik products against 
manufacturing defects in materials and craftsmanship. This warranty covers the fabric, 
seams, handles, and D-ring patches.

 

What your Warranty DOES NOT Cover:  

 

Your warranty does not cover cosmetic aging, UV damage, abrasion, abnormal abuse, 
inappropriate storage, general wear and tear or damage to your inflatable. 
 

 

This warranty can be void if your product is used or structurally altered beyond the 
reasonable limits of its intended use or structural capacity. 

 

 

Your product is covered from the original purchase date for the stated period of your 
product. When the original proof of purchase is unavailable the date of manufacturing 
will be used.  

 

Warranty Repair Procedures 

 

If you have an issue with your Zoik product please call 303.656.ZOIK for a return authorization 
number and shipping instructions. If the damage is a manufacturer’s defect or faulty 
craftsmanship, Zoik will pay for the material and labor required to repair your inflatable and will 
provide return shipping. You are responsible for shipping to the Zoik repair facility. If the 
damage is caused by general wear and tear, you are responsible for the materials and labor and 
return shipping expense.  Zoik reserves the right to repair or replace any product covered by these 
warranties and the right to replace any discontinued item with a current model when necessary. 
 

If you have any questions, please contact Zoik Inflatables. 

•   www.ZoikInflatables.com    •   [email protected]    •   303.656.ZOIK 

Thank you for choosing Zoik Inflatables.  See you on the water. 

Содержание AlterEgo I

Страница 1: ... chamber and will prevent the air from escaping 5 Insert the pump hose adapter into the valve on the boat 6 Inflate the boat chamber to a very soft pressure 7 Repeat procedure for the other chamber 8 Place the boat s floor inside the boat with the foot braces in front and position so the floor lines up with the bailing holes When correctly aligned completely inflate the floor making sure it fits s...

Страница 2: ... to help protect and increase the life of your boat Do not set push pull or drag your boat across sharp objects Do not over inflate your boat Clean your boat with soap and water Completely drain and dry the boat prior to storage Storage Short Term Storage Quickly clean dry deflate and roll loosely Long Term Storage Rinse off all debris Thoroughly clean boat with light soap and water and allow the ...

Страница 3: ...d Let the glue dry about 15 minutes or until no longer tacky Then apply a second coat of glue to both the patch and the area on the boat to be repaired This time just wait until the glue is almost dry but still a little tacky Place patch on damaged area Starting from the inside press out all air bubbles and roll patch firmly e Let dry for 20 minutes before continuing on your float trip f Remember ...

Страница 4: ...er The 2 3 and 5 year warranties cover all retail purchases on all Zoik products against manufacturing defects in materials and craftsmanship This warranty covers the fabric seams handles and D ring patches What your Warranty DOES NOT Cover Your warranty does not cover cosmetic aging UV damage abrasion abnormal abuse inappropriate storage general wear and tear or damage to your inflatable This war...

Отзывы: