background image

© Copyright 2020 Zoeller

®

 Co. All rights reserved.

SERVICE CHECKLIST

  

Electrical precautions. Before servicing the pump, always shut off the main power circuit. Make sure you are wearing 

insulated protective sole shoes and not standing in water. Under flooded conditions, contact your local electric company or a 

qualified licensed electrician for disconnecting electrical service to the pump prior to removal.

  

Pumps contain oil which becomes pressurized and hot under operating conditions. Allow 2-1/2 hours after shut down 

before servicing pump.

 

Condition

 

A.  Pump will not start or run.

  B.  Motor overheats and trips on overload.

  C.  Pump will not shut off.

 

D.  Pump operates but delivers little or no water.

 
  E.  Pump starts and stops too often.

  F.  Large red flashing light comes on at control  box.

  G.  Grease and solids accumulate in pit around pump.

Common Causes

Blown panel or circuit breaker fuse, low voltage, thermal overload open, impeller 

clogged, float switch held down or defective, incorrect wiring in control panel, water 

in cap assembly.

Incorrect  voltage, impeller  blocked, negative head (discharge lower than intake of pump).   

Pump runs continuously at low water level. Low oil level in motor shell.

Air lock, debris under float assembly, incoming sewage exceeds capacity of pump.

Intake clogged with grease or sludge, pump air locked (clear vent hole), low or 

incorrect voltage, clogged discharge line, operating near shut-off head.

Check valve stuck open. Sump pit too small to handle incoming sewage. Level control 

out of adjustment. Thermal overload tripping.

High water in pit. Check pump for clogging, or overload trip. See “A” and 

“D” above.

Break up solids and run pump with water running into the pit. Allow level to lower to 

the pump intake.  Continue until solids are cleared from the pit. Do not drain kitchen 

grease down the sink.

MAIL TO:

  P.O. BOX 16347 • Louisville, KY  40256-0347

SHIP TO:

  3649 Cane Run Road • Louisville, KY  40211-1961

(502) 778-2731 • 1 (800) 928-PUMP • 

FAX

 (502) 774-3624

Visit our website:

zoellerpumps.com

Содержание MX161













Отзывы: