ZOE PPM3 Скачать руководство пользователя страница 179

Страница: 179 / 214

April 2019

N i g h t i n g a l e P P M 3 U s e r ' s G u i d e

20-1

Accessories

20. Accessories

The following table shows the accessories approved by Zoe Medical for use with
the Nightingale PPM3.

WARNING

– Use only approved accessories with the PPM3. Using

non-approved accessories may result in damage to the monitoring
equipment, measurement error, or harm to the patient, and may void
warranty coverage.

Part Number

Description

ECG Monitoring Accessories

421-0014

ECG 3 Lead Set, US, 1.5 meter, Snap-On

421-0038

ECG 3 Lead Set, US, 3.0 meter, Snap-On

421-0110

ECG 5 Lead Set, US, 1.5 meter, Snap-On

421-0032

ECG 5 Lead Set, US, 3.0 meter, Snap-On

SpO

Monitoring Accessories

180-3014

SpO

Sensor, Reusable

180-3008

SpO

Extender Cable (4 foot)

180-3007

SpO

Extender Cable (8 foot)

NBP Monitoring Accessories

180-1004

NBP Hose

180-1022

NBP Cuff, Adult (26-35 cm)

180-1023

NBP Cuff, Large Adult (32-42 cm)

180-1029

NBP Cuff, Infant (8-14 cm)

180-1030

NBP Cuff, Child (13-20 cm)

180-1031

NBP Cuff, Adult Long (29-38 cm)

180-1033

NBP Cuff, Thigh (42-50 cm)

Monitoring Accessories

010-427

Oridion Smart CapnoLine Plus and FilterLine Sample Pack

Содержание PPM3























































































































































































































Результаты поиска

Содержание PPM3

Отзывы:

Похожие инструкции для PPM3

Бренды по названию

Популярные бренды

ZOE PPM3, Руководство пользователя

Результаты поиска

Содержание PPM3

Отзывы:

Похожие инструкции для PPM3

Бренды по названию

Популярные бренды