manualshive.com logo in svg

ZOE PPM3, Руководство пользователя

Пользовательское руководство для продукта ZOE PPM3 теперь доступно для скачивания бесплатно на {сайт}. Это подробное руководство поможет вам разобраться с функционалом и настройками устройства. Не упустите возможность загрузить его прямо сейчас!

Поделиться
Скачать
background image

 

 

 

April 2019 

N i g h t i n g a l e   P P M 3   U s e r ' s   G u i d e  

17-3

 

                                                                                       

 

Strip Chart Recorder Option 

 

17.3.  Strip Chart Recordings 

 
Strip chart recordings contain a waveform area that includes a 40 mm-wide grid 
with descriptive text above and below the grid. The waveform grid has major 
divisions at 5 mm intervals and minor divisions at 1 mm intervals, in both the x 
and y direction. 
 
The waveform area contains one or two user-selected waveforms.  If one 
waveform is selected, the waveform uses the entire grid.  If two waveforms are 
selected, each waveform uses half of the grid, with no overlap.  If the same 
waveform is selected for both waveform channels, it is treated as a single 
waveform selection (i.e., one waveform using the entire grid). 
 
Any displayed waveform may be selected for printing.  The printed waveform 
scaling and lead-off handling matches that of the displayed waveform.  The 
descriptive text above the waveform area describes the top waveform.  The text 
below the waveform area describes the bottom waveform (or is left blank if only 1 
waveform is printed).  The descriptive text includes the waveform label, the 
waveform scale and the associated parameter value.  For ECG waveforms, the 
frequency response (fixed at monitor) is printed.  Additionally, the descriptive 
text above the waveform area includes the current date/time, the waveform delay, 
and the sweep speed (fixed at 25 mm/sec). 
 
Strip chart recordings contain a trailer with the current date/time and a list of all 
parameters (label, value, and units of measure) that are currently on display. 
 
Alarm-generated strip chart recordings contain a header with an "Alarm 
Snapshot" banner and a list of the parameters (label, value, and units of measure) 
that are currently in alarm. 
 
When a strip chart recording is in progress, you can cancel it by pressing the Print 
key. 
 

Содержание PPM3























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PPM3

ABB S4Cplus Instruction preview
S4Cplus
Бренд: ABB Страницы: 86
DanMedical D-MAS HyperSat 2540 Instructions For Use Manual preview
D-MAS HyperSat 2540
Бренд: DanMedical Страницы: 103
B-K lighting LT Installation Instructions preview
LT
Бренд: B-K lighting Страницы: 3
JB-Lighting P18 Operating Instructions Manual preview
P18
Бренд: JB-Lighting Страницы: 32
W&H MS Instructions For Use Manual preview
MS
Бренд: W&H Страницы: 72
TAKAYA APT-9411 Series Service Manual preview
APT-9411 Series
Бренд: TAKAYA Страницы: 77
Tadano TR-800XXL4 Service Manual preview
TR-800XXL4
Бренд: Tadano Страницы: 402
Össur PROPRIO FOOT W Instructions For Use Manual preview
PROPRIO FOOT W
Бренд: Össur Страницы: 82
JBM 52489 Instruction Manual preview
52489
Бренд: JBM Страницы: 12
Abus TAS 112 Installation And Operating Instructions Manual preview
TAS 112
Бренд: Abus Страницы: 8
DeVilbiss PulseDose LT PD1000 Instruction Manual preview
PulseDose LT PD1000
Бренд: DeVilbiss Страницы: 58
V&P Scientific SpinVessel VP 418SV3-1-850RB-CC Operating Instructions Manual preview
SpinVessel VP 418SV3-1-850RB-CC
Бренд: V&P Scientific Страницы: 9
CORN MACDON C HARVESTEC 6000 Installation Manual preview
MACDON C HARVESTEC 6000
Бренд: CORN Страницы: 24
Star Sea Data Installation And User Manual preview
Sea Data
Бренд: Star Страницы: 16
Daihan Scientific HB-R48 Operation Manual preview
HB-R48
Бренд: Daihan Scientific Страницы: 27
R+M Suttner WEEDDEVIL ST-97 User Manual preview
WEEDDEVIL ST-97
Бренд: R+M Suttner Страницы: 16
Viking VK277 Instruction Manual preview
VK277
Бренд: Viking Страницы: 6
G2G Lighting Wensco AnPro180 Stick Quick Start Manual preview
Wensco AnPro180 Stick
Бренд: G2G Lighting Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды