background image

 

4 / 12 

 

ASSEMBLY 

 

Choose a smooth and clean surface 

 

 

IF THE BUOYANCY TUBE WAS STORED AT A TEMPERATURE BELOW 

0°C / 32°F, LEAVE IT  AT 20°C / 68°F FOR 12 HOURS BEFORE 

UNFOLDING. 

 

310 COMPACT 

 

No assembly is required 

 

275  ROLL UP : 

 

Boat deflated, slide the slats in their pockets starting by the closest to the transom. If the slats are 
difficult to insert, lubricate it with liquid soap. 

 

275 AERO – 310 AERO :       INFLATE THE HIGHT PRESSURE FLOOR 

 

 

           HP INFLATABLE FLOOR DEFLATED 

 

 

 

 

 

 

efore inflating, open out the boat and position the keel on the central band of the bottom and on the 
floorboard axis (centered between the positioning pins). 

 

FIRST 

inflate the keel-floorboard assembly to its rated pressure.

 

 

Check that the keel inflated perpendicular to the floorboard and that it is still positioned on the 
central band of the bottom (otherwise, reposition).

 

 

Inflate the main buoyancy tube.

 

 

Press the floorboard down around the edges to fit it into the hollow of the angle. 

 
 

MAINTENANCE / DISMANTLE OF THE HP INFLATABLE FLOOR 

 

We recommend that you leave the H2P floor in the boat when folding. 
To clean perfectly the boat proceed as follow: 
 
Deflate the boat and the floor. 
Inflate again the boat a little. 
Wash off with clear water and then raise the boat’s nose to evacuate water and sand or rubbish. 
Do not separate the keel from the floor nor from the buttom. 

Содержание WAVE 275 Aero



















Отзывы: