2-4
3. Assemble filter control valve into the filter tank.
a. Insert filter control valve (with o'ring in place) into the tank neck, taking care that the center pipe slips into the hole
b. Place two plastic clamps around valve flange and tank flange and tighten just enough so that the valve may be
d. Connect pump to control valve opening marked PUMP. After connections are made, tighten valve flange clamps with
plumbing connections, suction lines to pump, waste, etc.
5. Make electrical connections to pump per pump instructions.
6. To prevent water leakage, make sure all pipe connections are tight.
4. Make return to pool pipe connection to control valve opening marked RETURN and complete other necessary
MAIN DIMENSION
in the bottom of the valve.
rotated on tank for final positioning.
c. Carefully screw pressure gauge (with o'ring in place) into tapped hole in valve body. Do not over-tighten.
screwdriver, tapping around clamp with screwdriver handle to help seat valve flange clamp.
REPLACEMENT PARTS OF FILTER
3-4
1. Make sure the correct amount of filter media sand is located in the tank and all connections have been connected and secured.
2. Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve seal, always depress handle
before turning.)
3. Prime and start pump according to pump instructions (be sure all suction and return lines are open), allowing the filter tank to fill with
water. Once water is flowing out of the waste line, run the pump for at least 1 minute. The initial back-washing of the filter is
recommended to remove any impurities or fine sand particles in the sand media.
4. Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear, about 1/2 to 1 minute. Turn
pump off and set valve to FILTER position and restart pump. The filter is now operating in the normal filter mode, filtering dirt particles
from the pool water.
5. Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and tighten connections, bolts, nuts,
as required.
6. Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the pump and general piping
system.) As the filter removes dirt and impurities from the pool water, the accumulation of dirt in the filter will cause the pressure to rise
and diminish the water flow. When the pressure gauge reading is 1.5 bar, higher than the initial "clean" pressure you noted, it is time to
backwash the filter (see BACKWASH under filter and control valve functions).
NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually
INSTALL/START-UP OF FILTER
heavy initial dirt load in the water.
B
B
A
A
REPLACEMENT PARTS OF MULTIPORT VALVE
DIMENSION TABLE
A
B
Model
High
Diameter
mm
mm
845
TP500
535
950
TP650
635
mm
Valve Port
Size
Sand
kg
85
145
40
40
1020
TP700
710
210
40
Item
Part No.
1
W88280105 40mm Top Mount Valve
2
W89280101 40mm Union With Sight Glass, O-Ring
3
W89280102 40mm Union Set (2 Pieces) With O-Ring
W06021001 Plastic Pressure Gauge With O-Ring (35psi)
W01111048 Connector for Pressure Gauge/Stopper
W89010119 M6*50 Screws With Nut
W01271010 Clamp Lock
6
W02011134 O-Ring for Filter Neck
W01331008 TP500 Filter Tank
W01331010 TP650 Filter Tank
W01331009 TP700 Filter Tank
W89011605 TP500 Lateral Assembly with Center Pipe
W89011606 TP650 Lateral Assembly with Center Pipe
W89011607 TP700 Lateral Assembly with Center Pipe
9
W01172008 TP500-TP700 Laterals (126mm)
10
W89011601 Water Drain Set
11
W01111062 TP500-TP700 Filter Base
8
Description
4
5
7
Item
Part No.
Description
1
W01013003
Handle(Big)
2
W03018008
Pin for Handle
3
W01181001
Washer for Handle
4
W89280107
M6×30 Screw with Nut for Standard Lid
5
W01013004
40mm Top Mount Valve Standard Lid (Black)
6
W02011002 O-Ring for 40mm Valve Lid
7
W01181002
Washer for Spring
8
W03014001
Spring for 40mm Top Mount Valve
9
W02011022
O-Ring for 40mm Valve Rotor
10
W01021001
40mm Valve Rotor
11
W02311002
Spider Gasket
12
W01013007
40mm Top Mount Valve Bottom Body Clamp
（
black)
13
W01013011
40mm Diffuser
14
W02011001
O-Ring for Diffuser
15
W01013012
40mm Top Mount Valve Over Drain Diffuser
16
W02011134 O-Ring
17
W02011151 O-Ring for 40mm Connector
18
W01013015 40mm Connector (black)
19
W02011003 O-Ring for 40mm Union
20
W01171153 40mm Union (A/E)
21
W01013017 40mm Union Nut (black)
22
W01041002 40mm Union With Sight Glass (short)
23
W01172026 40mm Union With Sight Glass Holder
24
W01111048 Connector for pressure gauge/stopper
25
W89021703 Drain Plug with O-ring
26
W06011009 Oil Pressure Gauge With O-ring (50Psi)
