manualshive.com logo in svg

Zmotion ECI0064, Руководство пользователя

Поделиться
Скачать
Zmotion ECI0064 Скачать руководство пользователя страница 23

                                                                       

ECI0064 Network IO Control Card User Manual V1.5

 

Note:   

 

The times in the form are typical based on the resistive load, and may change 

when the load circuit changes. 

 

Due  to  the  leak-type  output,  the  shutdown  of  the  output  will  be  obviously 

affected by the external load circuit, and the output frequency should not be set 

too high in the application. For low-speed output, it is recommended to be lower 

than 8HKz. If there needs higher speed, please contact us to adjust parameter or 

custom hardware. 

→

 Wiring Reference 

 

→

 Wiring Note: 

⚫

 

The wiring principle of low-speed digital output OUT (0-31) is shown in the figure 

above. The external signal receiving end can be an optocoupler or a relay or solenoid 

valve, all can be connected as long as the input current does not exceed 300mA. 

⚫

 

For the connection of the public end, please connect the "EGND" port on the power 

supply to the negative pole of the DC power supply of the external input device. If the 

DC power supply of the external device and the controller power supply are in the 

same power supply system, this connection can also be omitted. 

3.3.2.

 

  Basic Usage Method 

(1)

 

Please follow the above wiring instructions to wiring correctly.   

Содержание ECI0064

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды