ZKTeco X8-BT Скачать руководство пользователя страница 10

Страница: 10 / 12



Configuring Tamper Alarm

Press

【

】

Press

【

】

to exit

Verify administrator

fingerprint

Press

【

】

【

】

Configure tamper

alarm switch

【

】

(0:enable

，

1:disable)

If this function is enabled, alarms will be raised when the device is dismantled from the wall.



Configuring Door Sensor Delay (default value: 10s)

When the door is not closed well after the set time period, the Door Sensor Alarm will generate

an alarm signal to alert the users.

Press

【

】

【

】

Press

【

】

to exit

Verify administrator

fingerprint

Press

【

】

【

】

Configure the door

sensor delay

【

】

(range

：

1s~254s)



Note:

①

Values greater than 254 are considered invalid. The indicator turns red and makes four short

beeps.

②

When an alarm is triggered, the device interior alarm will be triggered first. After 30 seconds,

the device exterior alarm will be triggered.

Содержание X8-BT













Результаты поиска

Содержание X8-BT

Отзывы:

Похожие инструкции для X8-BT

Бренды по названию

Популярные бренды

ZKTeco X8-BT, Руководство пользователя

Результаты поиска

Содержание X8-BT

Отзывы:

Похожие инструкции для X8-BT

Бренды по названию

Популярные бренды