DATA0
DATA1
GND
+12V
GLED
RLED
BEEP
Access
Control Panel
IWD0
+12V
BEEP
GLED
RLED
IWD1
GND
IP
Address
：192.168.1.100
Subnet
Mask
：255.255.255.0
IP
Address
：192.168.1.124
Subnet Mask
：255.255.255.0
Switch
…
Side
View
Back
View
Tamper
Magnet
Reset
Button
485
+
RS485
+
485
-
RS485
-
485+
485-
485+ 485-
RS
485
Bus
485+ 485- 485+
485-
RS
485
10. Cautions:
6. Wiegand Output
The device supports standard
Wiegand 26
output,
so you can connect it with most of the access control
7. Wiegand Input
connect with
card
reader. They
an independent
are installed each
The device has the function of
Wiegand
input
upports to
signal
. It s
Wiegand signal extender in long distance or interference
environment
).
(2) To keep the stability of Wiegand signal, connect the device and the Access Control or Card Reader in same ‘GND’
(1) Please keep the distance between the device and Access Control or Card Reader less than 90 meters
(
Please
use
There are two modes that the PC software communicate and exchange information with the device: RS485 and TCP/IP, and
supports remote
control
.
9. Communication
8
.
Other
Functions
(1) Manual Reset:
(2) Tamper Function:
(
A
)
Crossover
cable
:
The
device and PC connected
(
B
)
Straight cable
:
The device and PC connected to
(2) TCP/IP Mode:
(1) RS485
Mode:
other
restart it.
abnormality, you can use ‘Reset’ function to
button hole with
than 2mm).
a
sharp
tool (the tip diameter less
Operation:
Remove
the
black
rubber cap
,
then stick
the
Reset
If
the
device
does
not
work properly because of misoperation or
In
device
installation, user need to put a magnet between the device and
the back plate. If the device being illegally
, and the magnet being
moved
away from the device, it will trigger the alarm.
(
2
)
We
recommend the
3
DC
A
/
12V
power
supply
.
Please contact our technical staff
for
details.
(
5
)
Please connect the ‘GND’
before all the other wiring especially under the environment with much electrostatic.
( )
3
Please
read
carefully
the
terminal
description
and
wiring
by
rule
strictly
.
Any
damage
caused
by
improper
(
4
)
Keep the
exposed
part
of
wire less than 5mm
, to avoid unexpected connection.
(
6
)
Do not change the cable type because of long distance between the power and the device.
(
1
)
Power
cable
is
connected after all the other wiring.
If the device is working abnormally, please shut down the power
first, then make the necessary check . Kindly reminds you that any hot-plugging may damage the device, and
operations will be out of the range of our guarantee
.
it is not included in the warranty.
Terminals
PC
Serial
Ports
Converter
！
Warning: No operating with power on
in any case.
side of the door, to control the lock and access together.
Please use specified RS485 wire, RS485 active converter and
bus-type wiring.
Terminals definition please refer to the right table.
LAN/WAN through switch/Lanswitch.
Two ways for TCP/IP connection.
directly.
devices by now
.
485+
485-
TXD
RXD
GND
GND
WD0
WD1
DATA0
GND
DATA1
(7) Please use specified RS485 wire, RS485 active converter and bus-type wiring. If the communication wire is longer than
100
meters, it is needed to parallel a terminal resistance on the last device of RS485 bus, and the value is about 120 ohm.
