background image

P-17

P-18

Operating status

Power on checking

NO.

 

1

 2

 3
 4

 5

 6

Check content

Check and ensure the circuit breaker for the EV

 

charger is reasonably selected

Confirm that there is no short circuit between the
AC output L/N/PE of the charging

Confirm that the charging gun is not connected to

 

the vehicle

Ensure the circuit breaker is closed
The charger is powered on, and the power-on selfcheck is 
completed in about 10 seconds

After the power-on self-check is completed, observe

 

the status of the LED 

indicator.Normal standby: Green breathing light ON. 
Equipment Failure: Yellow light on /Red light on (Please find below for reference)

LED light instructions

Operating status

EV Charger

Emergency stop protection

CP signal abnormal

Poor grounding/Nature and live wire
reverse connection

Over-voltage 
Protection

Under-voltage 
Protection

Over-current

 

Protection

Temperature

 

Protection

Leakage

 

Protection

LED light

Yellow light on

Yellow & Red LED flicker
alternately (interval 1s)

Red light ON

Red light flashes (flashing once every
500MS and

 

then repeating after

waiting 2 seconds)

Red light flashes (2 flashes at 500MS 
intervals, and then repeats after
waiting for 2 seconds)

Red light flashes (interval 500MS)
Red light flashes (interval 200MS)

Red light flashes (interval 500MS

 

flashes 3 times,wait 2 seconds 
and repeat)

LED board is Offline

The yellow light is on once and then
flashes 2 times

 

intermittently (after

the yellow light is on for 1second,
it flashes 2 times and 2 seconds at an
interval of 250MS)

DLB Offline

Current abnormal

The yellow light is on once and the red
light is flashing once intermittently 
(after the yellow light is on for 1 second,
 the red light flashesonce at 250MS
intervals and repeats after 2 seconds.
The yellow light is on once and the red
light is flashing 2 times intermittently 
(after the yellow light is on for 1 second, 
the red light flashes 2 times and 2
seconds

 

at an interval of 250MS)

EV Charger

No Power

Power ON Checking

Stayby

Plug the connector without swiping RFID
 (not ready to charge) 

LED light

LED OFF

Plug the connector without swiping RFID 
(ready to charge)

Green,Yellow,Red Lights ON and OFF

Green Light ON

Streaming light runs back and forth

Streaming light runs fast back and forth

Plug the connector with RFID swiped
 (not ready to charge)

Charging

streaming light runs from 
two ends to the middle

Streaming lights from the
middle to up and down

RFID initiated without charger inserted

green light on the upper,last for 1 min

Charing without current

LED lights runs from middle to 
the end (not to the bottom).

Charging with S2 disconnected

green light all on

Содержание BCP Series


























Отзывы: