ZIV SW3 Скачать руководство пользователя страница 48

Страница: 48 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

48/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

Management is accessible through all ports because they operate as connected to a

Primary VLAN, regardless of the fact that the user assigns this behaviour to other

interfaces.

FIGURE 26 shows an example where Primary VLAN is number 100, Isolated VLAN is 200,

there are two Community VLANs, 300 and 400, and an Isolated Community with identifier

500.

In FIGURE 26, devices connected to ports with VLAN 200 can only communicate with

devices located in the WAN, and can not do so with each other. Devices connected to the

VLAN 300 can communicate with devices located in the WAN and with the rest of devices

connected in the same VLAN, analogously for devices with VLAN 400. Devices connected

to VLAN 500 will be able to communicate with each other within the same switch, but not

with devices connected in another switch, although they can communicate with devices

located in the WAN.

FIGURE 26

PVLAN example

5.6

BANDWIDTH LIMIT CONFIGURATION

The

Rate Control

menu permits bandwidth limits to be selected in each one of the ports,

both incoming and outgoing. The data volume limit may be selected in general for all types

of traffic, as well as for certain combinations that take into account the type of messages.

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 48 / 122

Результаты поиска

Содержание SW3

Отзывы: