background image

Page 6 of 28 

   802411 v3.05 09.20 HT BC Compact Instructions

Important Safety Instructions

This manual contains important safety and installation instructions for the Zip HydroTap G4.

Safety

This appliance is not intended for use by persons (including children) with reduced physical, sensory or 

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or 

instruction concerning use of the appliance by a person responsible for their safety. Children should be 

supervised to ensure that they do not play with the appliance.
For products sold in Europe, this appliance can be used by children aged from 8 years and above and 

persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they 

have been given supervision or instruction concerning use of the appliance in a safe way and understand 

the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be 

made by children without supervision.

Refrigerant

The Zip HydroTap unit contains R134A refrigerant under pressure. Maintenance of the refrigeration unit must 

be carried out by an accredited service provider or qualified refrigeration technician.

Qualifications

If the power cable is damaged it must be repaired only by a qualified technician. To avoid hazards, all 

Installation procedures must be carried out by a suitably qualified tradesperson. The power cable and power 

outlet must be in a safe visible position for connection.

Venting

Sometimes steam and / or condensed droplets may discharge through a vent outlet at the tap. If the tap is not 

installed using the Font pedestal, ensure the tap body is located so the tap outlet safely dispenses into the 

sink bowl area. 

Lifting

Take care when lifting the Zip HydroTap unit. Some units may exceed safe lifting limits. If you feel this is 

beyond your personal capabilities, please seek assistance with the lift. The weights of the units are marked 

on the packaging. Do not lift the unit by the front cover or any connections at the top rear of the unit. Refer to 

the technical specification for the weight of your product. 

Airflow

The ambient operating temperatures, when installed in a cupboard, must be between 5ºC -  35ºC. The 

system will operate satisfactorily only if proper air ventilation is provided and only if the recommended air 

gaps of 50mm on each side are provided. See section 2 for correct Installation details. 

Altitude

Water boils at varying temperatures at different altitudes. Your HydroTap adjusts for this during startup 

calibration and will recalibrate itself on a regular basis. 

Frost Protection

If this appliance is located where the ambient air temperature could fall below 5ºC when the heater is not 

in use, do not turn off the appliance electrically. This safeguard does not offer the same protection to the 

connecting pipework and fittings.

!

Содержание 2824AU0W0ZN1C





























Отзывы: