ZIMO MS450 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 88

background image

MS - SOUND decoders MS440 to MS990 and MN - NON-SOUND decoders MN170 to MN340 Page 23

CV

Denomination

Range

Default Description

#8

Manufacturer

ID

and

HARD RESET

by CV #8 = „8“

or CV #8 = 0

Read only

always

shows “145”

for

ZIMO

ID

Pseudo-

programming

see descr.

on the right

145

(= ZIMO)

Reading out this CV always result in “145” (10010001),
the number issued for ZIMO by the NMRA.

This CV is also used for various resetting processes
with the help of Pseudo-Programming.

“Pseudo programming” means that the entered value is not really
stored, but rather used to start a defined action.

CV #8 = “3”

→

21MTC decoder FO3, FO4 logic-level

CV #8 = “4”

→

21MTC decoder FO3, FO4 normal

CV #8 = “5”

→

21MTC decoder FO5, FO6 logic-level

CV #8 = “6”

→

21MTC decoder FO5, FO6 normal

CV #8 = “8”

→

HARD RESET (NMRA standard);

all CVs return to the last active

CV set or

sound project,

or (if no such set was active before)

the default values listed in this CV table.
CV #8 = “0”

→

NOT recommended (service purp. only)

Default values of the CV table

#7

SW version number

Also see CV #65

Sub-Version number

and

Auxiliary procedure for pro-

gramming via

"Lokmaus-2" and similar

"low level" - systems

Read only

-

CV holds the firmware vers. no currently in the decoder.
CV #7 = number of the

“main” version

CV #65 = Sub-version number

At the same time this CV is used to make digital sys-
tems with limited number space (typ. example: old Lok-
maus) usable for programming the decoder by means
of "pseudo-programming":

Ones digit = 1: Subsequent programming value + 100
                  = 2: ... + 200
Tens digit = 1: Subsequent CV 100
                      = 2: ... + 200
          etc. = 9: ... + 900
Hundreds digit = 0: Revaluation valid for one operation
                          = 1 ... to power-off

#65

SW

Sub-Version Number

Also see CV #7 for

Version number

Read only

-

If there are subversions to the SW version in CV #7, it
is read out in CV #65.
The entire SW version number is thus composed of
CVs #7 and #65 (i.e. 28.15).

#248,

#249

Bootloader

version and subversion

Read only

-

Reading out these CVs provides the version and sub-
version of the bootloader currently on the decoder
(bootloader = program to load the actual software).

«
...
21
22
23
24
25
...
»

Содержание MS450

























































































Отзывы:

Нет отзывов

Похожие инструкции для MS450

Бренд: Omega Engineering Страницы: 10

Бренд: Lenze Страницы: 132

Бренд: Harman Kardon Страницы: 16

samlexsolar SPB-EXPLORE200

Бренд: Samlexpower Страницы: 2

Бренд: Vitek Страницы: 32

Бренд: IMO Страницы: 94

Бренд: iLive Страницы: 12

COMMAND VALVE P1012593

Бренд: Ideal Vacuum Страницы: 9

PROFINET Master HD67B70-232-A1

Бренд: ADF Web Страницы: 31

Бренд: POWER ON BOARD Страницы: 13

Бренд: Mitsubishi Страницы: 143

Бренд: National Instruments Страницы: 53

Бренд: I-Tech Страницы: 16

Бренд: Growatt Страницы: 25

Бренд: UCEC Страницы: 22

Бренд: R&S Страницы: 24

Бренд: MRC Страницы: 2

SitePlayer Telnet Series

Бренд: NetMedia Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды