background image

6

BitStorm 4800 Express Model 4821-A2 Installation Guide

4821-A2-ZN21-30

EMI Notices

UNITED STATES – EMI NOTICE:

This equipment has been tested and found to comply with the limits 

for a Class A digital device, pursuant to Part 15 of the FCC rules. 

These limits are designed to provide reasonable protection against 

harmful interference when the equipment is operated in a 

commercial environment. This equipment generates, uses, and can 

radiate radio frequency energy and, if not installed and used in 

accordance with the instruction manual, may cause harmful 

interference to radio communications. Operation of this equipment in 

a residential area is likely to cause harmful interference in which case 

the user will be required to correct the interference at his own 

expense.

The authority to operate this equipment is conditioned by the 

requirements that no modifications will be made to the equipment 

unless the changes or modifications are expressly approved by 

Paradyne Corporation.

If the equipment includes a ferrite choke or chokes, they must be 

installed per the installation instructions.

CANADA – EMI NOTICE:

This Class A digital apparatus meets all requirements of the 

Canadian interference-causing equipment regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du 

réglement sur le matérial brouilleur du Canada.

!

!

Содержание 4821-A2























































Отзывы: