ZF CruiseCommand 785CE Скачать руководство пользователя страница 56

Страница: 56 / 160

ADJUSTMENTS AND TESTS [AT DOCK]

Page 48

7.5 E

NGINE

TOP

WITCHES

EST

NGINES

UNNING

)

A)Start engine(s).

B)Verify that all Engine Stop Switches function correctly at all sta-

tions.

Refer to information supplied by engine manufacturer or switch sup-
plier for set-up and adjustments.

7.6 W

ARM

-U

ODE

EST

NGINES

UNNING

)

A)Place the Control Head lever(s) in the Neutral position.

B)Depress and hold the station transfer button.

C)Move the Control Head lever(s) to the Ahead detent position.

D)Release the station transfer button.

• If the red indicator light blinks, Warm-up Mode has been acti-

vated. Continue with Adjustments and Tests.

• If the indicator light does not blink, refer to Section 5.3, and

verify all connections are correct. Make any necessary
changes and then repeat this Section.

CAUTION: An Engine Stop Switch at each station is an absolute requirement. Refer to CFR46,

SEC. 62.35-5 and ABYC P-24.5.8.

WARNING: Do not attempt to continue tests until Engine Stop Switches function correctly.

NOTE: Use Warm-up Mode on each engine at each Station, one engine at a time to confirm speed

command.

Содержание CruiseCommand 785CE

































































































































































Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды

ZF CruiseCommand 785CE, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды