ZF CruiseCommand 785CE Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 160

background image

INSTALLATION

Page 21

E) Repeat for all Processors.

5.2.3 Control Head Harnesses

There are two choices of Control Head Harnesses depending on the type

of Control Head being used with this application.

• Plug at Processor end of harness only. (terminal connection Control

Heads)

• Plug at Processor and Control Head ends. (Plug connection Control

Heads)

The distance of the Control Head from the Processor is limited to the

length of an uninterrupted 7-conductor harness. This cable may never be
spliced.

A) Install the Control Head Wire Harness between each Control Head

and the appropriate Processor.

B)

Label

each harness at

both ends

with the station it connects, and

Port, Center, or Starboard for Multi Screw applications.

When installing the harness, support using clamps or straps not more than

18 inches

(0,5m)

apart, unless contained in a conduit. Refer to ABYC Stan-

dard E-9.

Install each harness so it is protected from physical damage.

See Section 5.3.2 for cable connection at the Control Head.

5.2.4 Alarm Circuit (optional)

Refer to Section 9.1 in the Options Section.

5.2.5 Clutch Pressure (optional)

Refer to Section 9.2 in the Options Section.

5.3 C

ONTROL

H

EADS

See Appendix A.1 Control Head Dimensions and Variations for loca-

tion of cutout and mounting holes for the Control Heads used with this
application. Refer only to the following Sections that relate to the
Control Heads used.

CAUTION:The most common source of trouble is loose wiring connections. Verify wiring connec-

tors are properly crimped and cannot be pulled out. Crimps and connections must be
made to the wire, not to the wire insulation. Verify all screwed wire connections are
secure.

«
...
27
28
29
30
31
...
»

Содержание CruiseCommand 785CE

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CruiseCommand 785CE

Бренд: ZALMAN Страницы: 20

MICROCOMPUTER MN103S

Бренд: Panasonic Страницы: 5

MICROCOMPUTER MN103S

Бренд: Panasonic Страницы: 21

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 2

WJMPU955 - PROCESSING UNIT - TMU

Бренд: Panasonic Страницы: 62

Бренд: Cabletron Systems Страницы: 21

Бренд: LaCie Страницы: 44

LaCie Ethernet Disk

Бренд: LaCie Страницы: 2

SATA II ExpressCard 34

Бренд: LaCie Страницы: 2

12big Rack Fibre 8

Бренд: LaCie Страницы: 9

Бренд: Quantum Страницы: 20

Pixie-4 Express

Бренд: XIA Страницы: 17

EXPANSION CARD X-DANTE

Бренд: Behringer Страницы: 65

Бренд: Dantel Страницы: 62

Бренд: Cypress Semiconductor Страницы: 19

Бренд: SilverStone Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды