ZF CruiseCommand 785CE Скачать руководство пользователя страница 24

Страница: 24 / 160

PLAN THE INSTALLATION

Page 16

4.0 PLAN THE INSTALLATION

4.1 P

ROCESSOR

(

) L

OCATION

Processors are spray proof, but must

not be immersed.

An engine room location of the Pro-

cessor is preferred.

• If the engine room is too small,

locate in any area where it is
accessible for electrical connec-
tions.

Bulkhead mounting preferred for ease

of access for wiring and adjust-
ments.

The Processor can be mounted in any

attitude as long as the LED on the
front cover is readable.

Do not mount the Processor on the

engine, on the transmission, or in
any location that will subject it to
excessive vibration.

Refer to Figure 15: for Processor dimensions.
Locate Processor(s) away from heat sources, such as engine exhaust

manifolds turbochargers. Allow 4 feet

(1,2m)

of clearance, or

more, between the Processor(s) and such heat sources.

Do not mount close to gas engine ignition systems, alternators, or

electric motors. Allow 4 feet

(1,2m)

of clearance between the

Processor and alternators or electric motors.

A threaded hole is provided for connection to the vessel’s bonding

system.

NOTE: ZF Mathers recommends that the control system be installed in accordance with ABYC E-

9 and P24.

NOTE: Read the Warranty in Appendix A.1. Improper mounting location may cancel warranty.

Figure 15: Processor Dimensions

CAUTION: Electro-magnetic fields can influence CruiseCommand’s electronic circuits.

Содержание CruiseCommand 785CE

































































































































































Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды

ZF CruiseCommand 785CE, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды