ZF CruiseCommand 785CE Скачать руководство пользователя страница 14

Страница: 14 / 160

OPERATION

Page 6

2.7 H

IGH

/ L

DLE

ODES

The CruiseCommand Control System offers two options of engine

IDLE RPM settings.

• Low Idle Mode (default setting)
• High Idle Mode. (an adjustable elevated Idle RPM)

2.7.1 Low Idle

Low Idle

is the normal engine Idle RPM.

When the System is initially powered up, it will always command Low

Idle.

2.7.2 High Idle

High Idle

RPM may be programmed during Set-up. The High Idle

maximum setting is 20% of full throttle.

2.7.3 Selecting Between High / Low Idle

To select between Low and High Idle (or vice versa) at the Station-in-

Command: (refer to Figure 6:)

A) The Control Head levers may be in any position.
B) Depress and hold the transfer button for 1/2 second and then

release.

• If the System was in Low Idle it will toggle to High Idle and vice

versa.

C) To return to the previous Idle setting, depress and hold the transfer

button again for 1/2 second and then release.

Figure 6: High/Low Idle Mode Selections

Содержание CruiseCommand 785CE

































































































































































Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды

ZF CruiseCommand 785CE, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды