ZF CruiseCommand 785CE Скачать руководство пользователя страница 120

Страница: 120 / 160

TROUBLESHOOTING

TRAIN-156 Rev.B 11/01

Page 24

1.8 P

ROBLEM

CENARIOS

Table 2: lists the various Error Codes followed by possible causes and

solutions. The Error Message will appear on the appropriate Port or
Starboard side only. These are not the only possible causes for the
Errors Messages listed, just possibilities.

Err

Title

Description

Communication Error Time-
out System 7

Communication with the system has been too long without a Refresh message.

Communication Error Time-
out System 8

Communication with the system has been too long without a Refresh message.

Communication Error Time-
out System 9

Communication with the system has been too long without a Refresh message.

Communication Error Time-
out System 10

Communication with the system has been too long without a Refresh message.

Over Voltage Fault

The applied battery voltage is above the expected limits for greater than 2 seconds.

Under Voltage Fault

The applied battery voltage is below the expected limits for greater than 2 seconds.

Reset Due to Software
Watchdog

The system has had an unexpected Reset, due to a software/ hardware problem.

Reset Due to Software Fault

The system has had an unexpected Reset, due to a software problem.

Reset Due to Hardware
Watchdog

The system has had an unexpected Reset, due to a software/ hardware problem.

Table 2: Problem Scenarios

Err

Cause

Solution

a) The Astern Clutch Solenoid is defective.
b) The Clutch Harness is incorrectly wired at the Gear Box.

a) Replace the Astern Clutch Solenoid.
b) Properly connect the Clutch Harness to the Astern Solenoid.

a) The Astern Clutch Solenoid circuit is Open.
b) The Astern Clutch Solenoid is defective.

a) Properly connect the Astern Clutch Solenoid.
b) Replace the Astern Clutch Solenoid.

a) The Neutral Solenoid is defective.
b) The Neutral Solenoid is incorrectly wired at the Gear Box.

a) Replace the Neutral Solenoid.
b) Properly connect the Neutral Solenoid.

a) The Neutral Solenoid circuit is Open.
b) The Neutral Solenoid is defective.

a) Properly connect the Neutral Solenoid.
b) Replace the Neutral Solenoid.

a) The Ahead Clutch Solenoid Circuit is incorrectly wired at the

Gear Box.

b) The Ahead Clutch Solenoid is defective.

a) Properly connect the Ahead Clutch Solenoid.

b) Replace the Ahead Clutch Solenoid.

a) The Ahead Clutch Solenoid Circuit is Open.
b) The Ahead Clutch Solenoid is defective.

a) Properly connect the Ahead Clutch Solenoid.
b) Replace the Ahead Clutch Solenoid.

a) The Troll On/ Off Solenoid is incorrectly wired at the Gear

Box.

b) The Troll On/ Off Solenoid is defective.

a) Properly connect the Troll On/ Off Solenoid.

b) Replace the Troll On/ Off Solenoid.

Table 1: Error Messages

Содержание CruiseCommand 785CE

































































































































































Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды

ZF CruiseCommand 785CE, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды