background image

 

Technical specifications 

  

General description:                                                                                                                                                                                                                                                                            

A stationary gas detection system consists of a detector (transmitter) and a central controller. The 
detector and the controller are connected with a  cable. The detector converts the gas concentration into 
an electric measurement signal and transmits it via the cable for processing to the controller. 
Gas detectors GS-220.BC.V.ZETA are intended for detection of explosive and toxic gases. They are 
suitable for detection of different gases depending on the gas detection element. 
 

Measuring method: 

The following measuring methods are used: 

1.

 

Catalytic sensors for measurement of explosive gases. 

2.

 

Electrochemical sensors for toxic gases. 

3.

 

Infrared sensors for CO2. 

4.

 

Semiconductor sensors for refrigerant gases. 

 

Table. 1 

DETECTED GASES 

See Table. Ordering codes  

Gas feed 

Diffusion 

POWER SUPPLY 

 

Working voltage 

12 

 30 VDC 

Power Consumption 

3W 

 

 

OUTPUT SIGNAL 

 

GS-220.BC.V.ZETA 

 20mA 

 

 

ENVIRONMENTLE CONDITIONS 

 

Working temperature 

-20 - + 50

Humidity range 

10 

 90% R.H. 

Atmospheric pressure range 

800 

 1100 hPa 

 

 

MECHANICAL 

 

Dimensions 

155 x 120 x 48mm 

Weight 

0,320kg 

Enclosure material 

Aluminium  

Ingress protection 

IP65 

Cable connection 

Cable gland(s) M16 (M20) 

 

 

CERTIFICATION 

 

Conformity mark 

CE 

ATEX certification 

ATEX II 2G Ex d (ib) ma IIC T4 Gb 

 

ATEX II 2D Ex tb (ib) ma IIIC T135oC IP65 Db 

 
 
 
 
 
 
 
 

Содержание ZetaGas GS-220.BC.V.ZETA.MET.100













Отзывы: