Please take a few moments to check all pack contents listed.
Please contact “Zest4Leisure” directly if any of the pack contents are damaged
or missing. Contact telephone: 01352 752555 option 1 or email:
Assembly requires 2 persons. All screw holes to be pre-drilled.
Tools required: Corded/Cordless Drill, Pozi-drive Bit/Screwdriver, 3mm Drill Bit.
Winchester Pergola Seat is now complete.
1.
Position 2no Rafters A 130mm from both ends of Short Rails B and fix using 4no 60mm Screws -
2 per Rafter (Fig.1a). Position remaining Rafter A centrally (Fig.1b) and fix using 2no 60mm
Screws.
2.
Position 2no Rafters A 470mm and 130mm from ends of Long Rail C (Fig.2a) and fix using 4no
60mm Screws
– 2no per rafter. Space out remaining Rafters A equally (Fig.2b) and fix using 4no
60mm Screws
– 2no per rafter.
3.
Ensuring predrilled bolt holes face outwards (Fig.3a) fix together 2no Corner Trellis Panels D1 to
form a corner using 4no 60mm Screws (Fig.3b).
4.
Position End Trellis Panel D2 to the Long Rail/Rafter Assembly as shown in Fig.4a and fix using
4no 60mm Screws
– 2no per post (Fig.4b).
5.
Position Corner Trellis Panel Assembly to the Long Rail/Rafter Assembly at 165mm from end of
Long Rail C as shown in Fig.5 and fix using 6no 60mm Screws
– 2no per post (Fig.5).
6.
Position End Trellis Panel D2 to the Short Rail/Rafter Assembly as shown in Fig.6 and fix using
4no 60mm Screws
– 2no per post (Fig.6).
7.
Attach 2no Long Braces E1 between End Trellis Panel D2 and Short Rail/Rafter Assembly using
6no 60mm Screws
– 3no per Long Brace E1 (Figs.7a & 7b).
8.
Attach Short Rail/Rafter Assembly to the Long Rail/Rafter Assembly as shown in Fig.8a using
4no 60mm Screws
– 2no per Short Rail B (Fig.8b)
9.
Attach the remaining 4no Long Braces E1 as indicated by arrows in Fig.9 using 12no 60mm
Screws
– 3no per Long Brace E1. Attach Short Brace E2 as indicated by arrow in Fig.9 using 2no
60mm Screws.
10.
Position Seat F between Corner Trellis Panel D1 and Side Trellis Panel D2 and align predrilled
bolt holes. Insert 3no Bolts and attach washers & nuts (Figs.10a & 10b).
11.
Attach Leg G to Seat F (Fig.11) using 1no Bold, washer & nut.
Repeat stages 10 & 11 for the remaining Seat F.
12.
Locate Table Top H between Corner Trellis Panels Assembly and Leg G and secure in position
using 4no 60mm Screws
– 1no per post (Fig12a) & 1no through Leg G (Fig.12b).
13.
Locate half lap joints of Seat Back J into half lap joints of Seat F and fix in position using 4no
40mm Screws
– 2no per joint (Fig.13a) and 2no 60mm Screws – 1no per post (Fig.13b). Repeat
procedure for the remaining Seat Back J.
14.
Attach Fascia K to Seat F using 4no 40mm Screws
– 2no per side (Fig.14). Repeat procedure for
the remaining Fascia K.
