Zero FX 2015 Скачать руководство пользователя страница 93

Страница: 93 / 136

General Maintenance

5.21

7. Unhook the headlight bulb spring clip (E) by pushing

down and to the side.

8. Lift up on the spring clip and remove the headlight bulb.

CAUTION:

Do not touch the glass portion of the headlight

bulb. Keep the headlight bulb free of contaminants. Oil
from your fingers or contaminants will shorten the life of
the bulb. Thoroughly clean any fingerprints or
contaminants from the bulb using a clean cloth moistened
with alcohol.

9. Install the replacement headlight bulb into the lens.

10.Installation is the reverse of the removal procedure.

Turn Signal Light Bulb Replacement

To replace the signal light bulb:

1. Remove the turn signal lens screw (A) and remove the

lens.

2. Push in on the bulb, turn the bulb counter-clockwise,

and then pull the bulb out.

3. Insert the new bulb into the socket, push in and turn

clockwise until it stops.

4. Install the lens and screw; tighten the screw. Do not

over-tighten the screw.

Zero Owner's Manual (FX).book Page 21 Thursday, April 5, 2018 1:40 PM

Содержание FX 2015









































































































































Результаты поиска

Содержание FX 2015

Отзывы:

Похожие инструкции для FX 2015

Бренды по названию

Популярные бренды

Zero FX 2015, Руководство пользователя

Результаты поиска

Содержание FX 2015

Отзывы:

Похожие инструкции для FX 2015

Бренды по названию

Популярные бренды