background image

2  •  Introduction

Important user Information 

Copyright © 2021 Zero Zone, Inc.

All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in any form or by any means including 

graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written 

permission of the publisher, Zero Zone, unless it is for the purchaser’s personal use. 

The information in this manual is subject to change without notice and does not represent a commitment on the part of Zero Zone. Zero Zone 

does not assume any responsibility for any errors that may appear in this manual. In no event will Zero Zone be liable for technical or editorial 

omissions made herein, nor for direct, indirect, special, incidental, or consequential damages resulting from the use or defect of this manual.

The information in this document is not intended to cover all possible conditions and situations that might occur. The end user must exercise 

caution and common sense when installing, using, or maintaining Zero Zone products. Zero Zone products should only be installed by qualified, 

professional refrigeration technicians. If any questions or problems arise, call Zero Zone at 800-247-4496.

Any change to a Zero Zone product made during the installation, start-up, or at any other time must be submitted in writing to Zero Zone for 

approval and be approved by Zero Zone in writing prior to commission. The product warranty is voided when any unapproved change is made 

to a Zero Zone product.

Manufacturer

Zero Zone, Inc. 

Display Case Division

110 N Oakridge Dr  •  North Prairie, WI 53153  •  800-247-4496  •  www.zero-zone.com

Intended use

Zero Zone products are intended to be installed and used as described in this manual and other related Zero Zone literature, specifications, 

drawings, and data. All Zero Zone products must be leveled after being installed.

Display Case Models

The information contained in this manual pertains to the following Zero Zone display cases:

CASE MODEL

DESCRIPTION

SILL HEIGHTS

ORMC82

82" Standard Multi-Deck (5-Deck)

Low (L), Medium (M), or High (H) Sills

ORMC87

87" Tall Multi-Deck (6-Deck)

Low (L), Medium (M), or High (H) Sills

ORMC75-MX

75" Meat Exclusive Multi-Deck (4-Deck)

Low (L) or Medium (M) Sills

ORMC80-MX

80" Meat Exclusive Multi-Deck (4-Deck)

Low (L) or Medium (M) Sills

ORMC80-PX

80" Produce Exclusive Multi-Deck (3-Deck)

Low (L) or Medium (M) Sills

ORMC82-PX

82" Produce Exclusive Multi-Deck (3-Deck)

Low (L) or Medium (M) Sills

INTRODUCTION

Reveal Merchandiser

®

 is a registered trademark of Zero Zone, Inc. in the United States.

Содержание Reveal Merchandiser ORMC75-MX
























Отзывы: