background image

Author: Rudi 

Version: 2.2 

Revision: 1.3 

Revision Date: August 2020 

 

the  guarantee  extended  on  the  unit  to  the  customer,  that  any  interference with  the 
filling  valve  screw  will  automatically void  the  guarantee.   The  absorption  unit  must 
not be opened, since it contains corroding chemicals under high pressure.

 

 

SERVICE NOTES

 

 

ROUTINE MAINTENANCE

 

It   is   recommended   that   a   suitably   qualified   person   service   this 
appliance at least once a year.

 

 

Inspect   the   gas   hose   for   cracks   and   chafing   marks.   Test   all 
connections with a suitable solution, 

do not use an open flame

 

Check  there  is  no  smell  of  ammonia  or  any  signs  of  green/yellow 
crystal-like  deposits  on  the  cooling  unit  tubes.  Smell  or  deposits 
indicate a leaking unit – see User instructions. 

 

Check   the   functioning   of   the   flame   failure   control   –   adjust   if 
necessary. 

 

Check  the  functioning  of   the  ignition  device  if  fitted  –  adjust  if 
necessary. 

 

-     

Check that the control knobs turn freely. 

 

Examine  the  burner flame  –  ensure burning  with  a  sharp  blue flame 
and no yellow tipping or sooting. 

 

-   

Check the door/lid seals are in good condition. 

 

 

IN THE EVENT OF FAILURE

 

 

If the burner will not light:

 

 

-     

Check adequate gas supply – through to burner. 

 

-     

Depress flame failure device for 15sec and try lighting with a match. 

This must be done in a well ventilated area!

 

 

QUALIFIED TECHNICIAN

 

 

Check jet is clean – if not, clean with solvent and blow dry. Do not try 
to clean with pin or similar. 

 

If  the burner will not stay alight, check position of  the thermocouple 
head, and the functioning of the safety valve. 

 

If not cold enough:

 

 

-     

Check through points listed under Troubleshooting. 

In  the  unlikely  event  of  cooling  unit  failure,  contact  the  national 
distributor without delay. 

Содержание GF120













Отзывы: