background image

Installa

tion - Moun

ting the R

ange Hood

 

 

MOUNTING HEIGHTS

The range hood must be installed at a minimum  
height of 24 inches (61cm) from the cooking 
surface. If a connecting duct work composed 
of two parts is used, the upper part must be 
placed outside the lower part. Do not connect  
the range hood duct to the same duct used to  
exhaust hot air or fumes from another appliance. 
Before proceeding with the assembly instructions 
remove the decorative mesh fi lters so that the 
range hood is esier to handle.

 

 

MOUNTING TO THE WALL

1. Place the paper template included with your 

hood on the wall to determine where to add 
the screws for mounting the hood. Make sure 
the bottom of the template aligns with the 
bottom of where the hood will be located. 
See Fig. 9

2. Lift the hood onto the screws (type 

D) and adjust to make sure the 
hood is level. 

3. When the hood has been adjusted 

tighten the screws to secure the 
hood in place.

NOTE:

 Screws must be fastened into 

wooden studs so wood blocking may 
be necessary. If using wall anchors 
make sure  to check your local codes 
for suitability and type of anchors 
to use.

NOTE1

: For the various installations use screws and screw anchors suited to the 

type of wall (minimum screw size: 1/4" diameter x 2-3/4" length).

Min 24" - Max 36"

36"

- 21 - 

Содержание Edge Wall AED - M90ASX




























Отзывы: