background image

www.zephyronline.com

Main

tencanc

e

  MAINTENANCE

• It is recommended to operate the appliance prior to cooking. It is recommended 
to leave the appliance in operation for 5 minutes after cooking is completed in 
order to completely eliminate cooking vapors and odors. The proper function 
of the range hood is conditioned by the regularity of maintenance.
• The decorative mesh fi lters capture the grease particles suspended in the air 
and are therefore subject to clogging because of frequent use. In order to pre-
vent a fi re hazard, it is recommended to clean the fi lter a minimum of every 2 
months or when instructed by the Metal Filter Clean indicator on the range hood 
controls. Clean the range hood by carrying out the following instructions:
- Remove the fi lters from the range hood and wash them in a solution of water 
and neutral liquid detergent, leaving to soak.
- Rinse thoroughly with warm water and leave to dry.
- Filters may also be washed in the dishwasher at the lowest setting.
The fi lters may alter in color after several washes but is not cause for replace-
ment.
• Clean the blower and other surfaces of the range hood regularly using a cloth 
moistened with denatured alcohol or non abrasive liquid detergent.

- 20 - 

Содержание ATI-M90ASX























Отзывы: