5
3
INSTAllATIoN
oPeRATIoN
1.
Choose a location for the fan which will ensure
adequate clearance from all objects and walls
and with blade height greater than 2.1 metres
from the floor.
2.
At the selected mounting position, check
whether there is a ceiling joist to which the fan
can be secured. If there is no suitable supporting
member, install a 50 x 100mm brace between
ceiling joists. Secure the mounting bracket to the
ceiling with four mounting screws and washers.
If a safety cable is provided with the fan,
anchor this securely to the supporting
member or mounting bracket when wiring
has been completed.
3.
Attach the downrod to the motor unit.
Firstly unfasten and remove downrod fixing bolts
and safety pins. Then remove the ball joint by
unscrewing the locating screw, sliding the ball
joint downward, and detaching the support pin.
5.
Hang the fan in the mounting bracket,
ensuring that the ball joint locating groove
aligns with the notch on the mounting
bracket. Do not connect to supply.
blade assemblY
6.
Place blade cover under blade and
bracket on top of blade as shown.
Secure each blade assembly
together with 3 screws.
7.
Attach each blade assembly to the
underside of the motor unit using
screws provided.
speaker assemblY
8.
Clip multi-pin electrical connector together, then position it
within the lower enclosure to protect it against damage.
After loosening safety screw attach speaker assembly by
pushing it upward then turning it to the right to fix into
position. When components are set in position lock
securely by tightening the two safety screws
(one on each side).
eleCTriCal ConneCTions
9.
Clip 4-pin electrical connectors together.
Connect supply Active, Neutral and Earth
wires to the supply terminal block.
10. Check all wiring, then push up top
canopy over mounting bracket and fasten
into position with fixing screw.
11. Switch power on at the switchboard and
check operation.
Pin
Locating
Screw
Locating
Groove
Blade Cover
(Fits Under Blade)
Blade Bracket
(Fits Over Blade)
Notch
Down Rod
4.
Feed the supply wires from the motor unit
through the downrod.
Ensure that the upper canopy is fitted over the
downrod before fitting the ball joint and fastening
downrod (reverse procedure to removal).
Multipin
Electrical
Connector
Connect Clips
Together
Supply Active
Supply Neutral
Supply Earth
2x Safety
Screws
2x Safety
Screws
Supply Terminal Block
4
Remove battery compartment cover and fit 2 x 1.5V AAA size batteries into the transmitter handset.
To operate the fan, press and release the designated button as shown below.
To enable the audio function, it is important to pair your device (phone, ipad, computer, etc.)
with the fan speaker system (see details in “pairing and using bluetooth function” section).
Press and release once to
change direction of fan blades.
Normal (default) direction
is designed to move air
downward, sometimes known
as “Summer” mode.
Reverse direction is designed to
move air upward, sometimes
known as “Winter” mode.
Refer to Summer/Winter
Operation instructions herein
Press and release
to turn on fan and
increase speed up
to level 4
Press and release to
enable fan to
automatically switch
off after 1 to 6 hours
Press and release to
enable Bluetooth
function.
Press and release to decrease
speed from level 1 down to
level 4.
Press and release to switch fan
off. Bluetooth Audio function is
not affected by this button
TransmiTTer handseT
Note 1:
The fan control operation of the transmitter handset is infrared type and must be directed at the
speaker of the fan (infrared receiver location) within a clear 8m distance.
Note 2:
Be patient when changing functions, in particular when changing from forward to reverse. Give
the fan time to recognize and react to the instruction.
Note 3:
The Transmitter Handset has a wall mount holder which can be attached to the wall with
2 screws.