background image

16. Warranty

WARRANTY TERMS

1) Scope of Application

This engine manufactured by Husqvarna Zenoah Co., Ltd. (herein after “Zenoah”). 

And sold to the user directly or through distributor/manufacturer, shall entitle to be

covered by this warranty.

2) Limits of Warranty

Zenoah warrants that;

1. The quality disclosed in the specifications.

2. The engine which shall be considered defective by Zenoah, caused by material or

production fault.

3) Limits of Compensation

1. Zenoah compensates such quality, material and production faults by repairing or

replacing through distributor/manufacture.

2. Zenoah shall not compensate any other accompanied or benefit losses caused to

user and distributor/manufacture by such faults and through repairing or

replacing.

4) Term of Warranty

Three (3) months after purchased by end- user subject to 12 months from produced

month.

5) Exempt from Warranty

Zenoah shall not warrant this engine even if the fault has been caused during the

period of terms of Warranty, in case that.

1. Any faults, failures caused from neglect of proper operation and maintenance

described in OWNER’S MANUAL.

2. Any modification not approved by Zenoah.

3. Normal abrasion and deterioration.

4. Consuming parts.

5. Using any parts which have not been certified by Zenoah.

6. Add-on or modified use. 

1-9 Minamidai, Kawagoe-city, Saitama, 350-1165 Japan

Phone: (+81)49-243-1117  Fax: (+81)49-243-7197

Содержание G231PUH





















Отзывы: