background image

GB-6

EXZ2600DL

4. Symbols on the machine

For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications,
please be careful not to make a mistake.

The port to refuel the “MIX GASOLINE”

Position: 

FUEL TANK CAP

The direction to close the choke

Position: 

AIR CLEANER COVER

The direction to open the choke

Position: 

AIR CLEANER COVER

If you turn the rod by screwdriver follow the arrow to the
“MAX” position, the chain oil flow more, and if you turn to
the “MIN” position, less.

Position: 

Bottom of the GEAR CASE

(PS-EX Only)

MIN

MAX

3. Warning labels on the machine

Never modify your machine.
We won’t warrant the machine, if you use the
remodeled brushcutter or if you don’t observe
the proper usage written in the manual.

If warning label peels off or becomes soiled and
impossible to read, you should contact the
dealer from which you purchased the product
to order new labels and affix them in the required
location(s).

15m (50ft)

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(1)   Read owner’s manual before operating this machine.
(2)   Wear head, eye and ear protection.
(3)   Wear foot protection.
(4)   Wear gloves.
(5)   Beware of thrown objects.
(6)   Warning / Attention
(7)   Keep all children, bystanders and helpers 15 meters away from the machine.

Содержание EXZ2600DL

































Отзывы: