manualshive.com logo in svg

Zenoah EX-BC, Руководство владельца/оператора

Поделиться
Скачать
Zenoah EX-BC Скачать руководство пользователя страница 27

8. Operation 

(Optional blade usage EX-BC only)

■

OPERATION

1. Check the bolt to fasten the blade and be sure

the bolt has no fault, and no abrasion.

2. Be sure that the blade and the holder have been

fastened according to instruction and the blade
turns smoothly without abnormal noise. (OP7)

• The rotating parts fastened incorrectly may

cause serious accident to the operator.

• Make sure that the blade is not bent, warped,

cracked, broken or damaged.

• If you find any error to the blade, discard it

and change new one which is certified by
RedMax.

■

By using the shoulder strap, hang the unit on
your right side. Adjust the strap length so that
the cutting head may become parallel to the
ground.(OP8)

Make sure to use shoulder strap and debris
guard. If not, it is vary dangerous when you slip
or lose your balance.

■

CONTROLLING BLADE BOUNCE

• Kick out can cause serious personal injury.

Carefully study this section.

It is important that

you understand what causes kick out, how you
can reduce the chance of kick out and how you
can remain in control of the unit if kick out does
occur. 

1. What causes kick out:

• Kick out can occur when the moving blade

contacts an object that it cannot cut. This contact
causes the blade to stop for an instant and then
suddenly move or ”bounce” away from the object
that was hit. The operator can lose control of the
unit and the blade can cause serious personal
injury to the operator or any person nearby if the
blade contacts any part of the body.

WARNING

WARNING

WARNING

EX-BC
OP7

EX-BC
OP8

27

Содержание EX-BC





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды