Zenith CM-150 Series, Руководство по обслуживанию

Страница: 10 / 54

CM150/PV150 1-4 GM CHASSIS
PROGRAMMING THE REMOTES
PROGRAMMING THE MBR3457 REMOTE
If you’re using Zenith products, the remote is already
programmed for the most common codes: TV = 101, VCR
= 201, CABLE = 353, and AUX = 401. For other brands, or
if your remote fails to control your Zenith products,
you’ll have to program the remote.
1. Make sure batteries are installed .
2. Press and hold PRG using a blunt pointed object.
Release PRG after indicator light turns on.
3. Press and release button for product being
programmed.
4. Enter 3-digit product code from Remote Control
Programming Codes in this section.
5. Press and release ENTER to save code.
6. Point remote at product and press POW ER to test
product operation. If it does not turn on, reprogram
remote using a different code.
TO AUTO FIND A CODE
1. Turn On the product you want to operate.
2. Press and hold PRG using a blunt object.
3. Press the key to be programmed: CATV, VCR, AUX, or
TV.
4. Enter “0-0-0,” then press ENTER within two seconds.
5. Point remote at the product.
6. Press and release POW ER repeatedly, about once a
second, until your product turns Off.
7. Press ENTER immediately to save the code.
8. Press POW ER to turn On your product.
9. Test your product. If the remote fails to operate the
functions you use most often, use Auto Find again to
search for a better code. (Auto Find resumes its
search after the last code that was entered and saved
in step 7.)
NOTE: If the indicator light stays on as you press
POWER, Auto Find has tried all of the codes.
If the product you want to control has not
turned off, your remote will not work with
that product.
To cancel Auto Find, press PRG at any time.
PROGRAMMING THE TRK4000 REMOTE
1. Select equipment needed to be programmed, turn to
page 2 - 5 to find the programming code appropriate
for the type and brand of equipment. Make sure the
equipment is turned on.
2. Point the MBR Trakball remote at the piece you’re
programming, press MUTE and FLSHBK at the same
time. Hold until one of the mode indicator LEDs
lights.
3. Use the MODE Right/Left button to select the
appropriate mode for equipment.
4. With the Number Keypad, enter the three digit code
found in step 1 and press ENTER . If the code is
accepted, the mode indicator Led will blink three
times, If it is not accepted, the Led will not blink.
NOTE: The TV and VCR modes will only accept codes
for those types of products. The AUX 1, AUX
2, and Cable modes will accept codes for any
kind of product.
5. Push the POW ER button to turn off the equipment. If
nothing happens, repeat the process from step 1,
and try the next code number.
NOTE: To get out of Programming before you enter
a code, just press the QUIT button on remote.
TO AUTO FIND A CODE
1. Turn on device you want to operate.
2. Press and hold MUTE and FLSHBK until the indicator
light turns on.
3. Press MODE Left/Right until the indicator light is
underneath the device needed to be programmed.
4. With the NUMBER keypad, enter the code 0-0-0
(zero-zero-zero), then press the ENTER key right
away.
5. Aim remote at correct device and push the POW ER
button. Allow a second to pass, then push the Power
button again. Repeat until the device turns off.
6. Push Enter to save the code. The indicator light on
the remote will blink three times and then turn off.
7. Press Power to turn the device back on.
NOTE: You can get out of Auto Find quickly by
pressing the Quit button.
If the indicator light does not turn off while
you push the Power key, all the codes have
been tried and your device can’t be
programmed.