46
2
Turn the hose end clockwise until it clicks into place.
3
Connect the other end of the hose (handle) with the
telescopic suction tube. In order to do so press the locking
device
“A”
and slide the tube into the hose handle so that
the locking device
“A”
is blocked in opening
“B”
.
4
Select the needed length of the telescopic suction pipe
by sliding the slider according to the arrow, and pulling out/in
the pipe.
5
Install a nozzle or a brush on the other end of the suction
pipe.
6
Use combination carpet & floor brush for vacuuming both
hard surfaces and carpets. To clean hard surfaces – wooden
floors, plastic floors, ceramic tiles etc. pull out the brush by
pressing the switch on the combination brush according
to the figure
. Retract the brush when vacuuming
carpets (set the switch in “
”).
7
Grab the plug of the cord
(4)
, and pull it out of the
vacuum cleaner.
When pulling out the cord pay attention to
the yellow band which marks the end of the
cord. Any attempts to unwind the cord further
(especially forcefully pulling on it) may lead to
damaging it.
8
Put the plug of the cord in an electric socket.
9
Press the on/off switch
(7)
to start the vacuum cleaner.
10
The vacuum cleaner is equipped with an electronic
controller of suction power, which enables smooth regulation
of suction power of the vacuum cleaner. By turning the knob
(8)
right or left – you can increase or decrease the suction
power.
11
The vacuum cleaner is also equipped with a mechanic
suction power controller
(3)
, which is situated on the hose
handle. You may use it to slightly regulate the suction power
without the need to use the knob
(8)
.
(De)installing the SAFBAG-type bag
E
The vacuum cleaner is equipped with safety
valve located in chamber of dust container
(bag). It opens automatically in case of total
stopping of suction hose or total stopping of
equipment elements connected thereto, as well
as in case of overfill of dust bag. After opening
the valve one can hear characteristic “whirr”
sound inside the vacuum cleaner.
1
Total covering up of bag loading indicator by the red
cover in case the sucker or the brush is upraised over
the cleaned surface informs, that change of dust bag is
necessary. The bag loading indicator may operate in case
of suction hose stopping or in case of stopping of equipment
elements connected thereto.
2
Press the on/off switch
(7)
to stop the vacuum cleaner.
3
Remove the plug of the cord from the socket.
4
Turn the suction tube end counterclockwise and remove
it from the inlet opening.
5
Release the fastening of the upper cover
(10)
, and open it.
6
Tilt bag’s handle and remove the bag.
7
Place the bag plate of a new bag into the guides of the
SAFBAG handle, and slide it to the limit. The direction in
which you should install the bag is marked by an arrow on
the bag.
8
Close the cover by pressing it, until you hear
a characteristic “click” – be careful not to trap the bag.
Do not start vacuuming without the SAFBAG-
type bag.
You have to replace the bag, if:
a) the red field covers the bag full indicator,
b) the vacuum cleaner works less efficiently,
c) the bag is full.
The number of SAFBAG bags set that can be purchased,
is placed on a sticker located in the vacuum chamber.
Filter disassembly
In case of getting the inlet filter (16), the outlet
filter (14) dirty, you can replace them, clean
them or rinse them with running water.
It is forbidden to wash filters in washing
machines or dishwashers.
Filters may be dried only naturally.
Do not use hairdryers, heaters or radiators to
dry filters.
Before replacing the filters make sure the
vacuum cleaner is off, and the plug of the cord
is unplugged from the socket.
INLET FILTER
1
Turn the suction tube end counterclockwise and remove
it from the inlet opening.
2
Release the fastening of the upper cover
(10)
, and open it.
3
Tilt bag’s handle and remove the bag.
4
Slide pre-filter holder out the guides located on the rear
wall of the vacuum cleaner chamber.
5
Remove the pre-filter from the holder.
If the inlet filter
(16)
is dirty, you may replace it with a new
one, clean it or rinse it with running water. Before reinstalling
the filter, make sure it is dry.
For safety reasons it is unacceptable to install
a wet or damaged inlet filter (16).
6
Fit a new pre-filter in the holder.
7
Insert the holder fitted with the new pre-filter all the
way into the guides located on the rear wall of the vacuum
cleaner chamber.
C
