Zelmer ZSF1410, Руководство пользователя, Страница: 6 / 31

11 10
PL PL EN EN
ASSEMBLY
Warning: the fan may be used only if it is fully and properly assembled, that is to say, complete with the
base and the grille.
Warning: always disconnect the appliance from the mains supply before assembling. if in doubt, have
the operation checked or carried out by a qualified technician. For the assembly refer to Fig. 1.
ASSEMBLE OF BASE
Set the column in place on the base and secure it using the “L” screw with washer while also engaging
the counterweight.
Make sure column and base and counterweight are firmly coupled.
Insert the upperpart tube into underpart, tighten with the height adjustment knob,
Insert the neck and the motor part into the upper part column and tighten with the height adjustment nut,
If necessary, you can only set the underpart column use as the floor fan. Make sure the Set Screw is
tightly secured.
ASSEMBLE OF BLADE AND GRILLE
Unscrew the plastic mounting nut from the front of the motor housing by rotating it anticlockwise.
Position the rear grille against the front of the motor housing with the handle uppermost, ensuing that the
locating pegs on the motor housing are engaged correctly in the holes of the rear grille.
Tighten the Rear Grille Mounting Nut clockwise. DO NOT OVERTIGHTEN IT.
Push the fan blade onto the motor shaft, locating the slot at the back of the blade on the drive pin that
passes through the motor shaft.
Tighten the blade cap by turning it anticlockwise.
Position the front grille against the rear grille so that the holes in the rims that accept the small nut and
bolt are in line. Insert the bolt through the holes and screw on the nut. Do not fully tighten at the stage.
Push the grille retaining clips into position ensuring that they engage correctly on the rim of the grille.
Fully tighten the small nut and bolt that passes through the rim of the grille.
USE
Before each use check that the appliance is in good condition and that the electric cable is not dam-
aged; if the electric cable is damaged, it must be replaced by the manufacturer or by the technical
assistance service or, in the event, by a qualified technician, in order to avoid any type of danger.
Insert the plug into the mains socket.
Set wind speed
Adjust the fan speed by rotating the speed switch.
0. OFF
1. Low Speed
2. Medium Speed
3. High Speed
Set Oscillation (Fig 2)
Set oscillation by pulling and depressing
oscillation knob on the motor cover.
Pull up: Stop Oscillation
Depress: Oscillation
It is necessary to disconnect the appliance
before assembling, disassembling and cleaning.
IMPORTANT WARNINGS
This appliance is intended exclusively for domestic use for ventilation of rooms: do not use it for other
purposes. Any other usage should be considered improper and dangerous. The manufacturer shall not
be held responsible for any damage resulting from improper, incorrect and irresponsible use and/ or for
repairs made by unqualified technicians.
Do not insert fingers or any other objects through the fan’s protector grille. The appliance must be kept
out of the reach of children.
Do not use the appliance if it is not working properly, or if it appears to be damaged; if in doubt, take it to
a professional, qualified technician.
Do not move the appliance while it is operating.
When the appliance is not being used, remove the plug from the mains socket. Do not touch the
appliance with wet hands or feet.
Do not drag the appliance by the cable to move it.
Do not pull the cable or the appliance itself to remove the plug from the mains socket.
To clean the appliance, follow the instructions in the section of the manual dedicated to cleaning and
maintenance.
EUROGAMA Sp. Z o.o. will not be held liable for any harm or damage which may occur to people,
animals or objects as a result of failure to observe the aforementioned warnings.
INSTALLATION
After removing the packing, check the condition of the appliance; if in doubt, do not use it and take it to a
professional, qualified technician. The packaging (plastic bags, polystyrene, fixtures, etc.) should be kept
out of the reach of children, since they are a potential source of danger, and they should be disposed of
in the appropriate specific containers for selective waste collection. Warning: any stick- ers or leaflets
attached to the grille must be removed before using the appliance.
Before connecting the appliance, check that the voltage values indicated on the characteristics plate
correspond to those of the electric mains supply. In the event that the mains socket and the appliance
plug are incompatible, have the plug changed to one that is suitable by a professional, qualified
technician. They will check that the cable part of the plug is adapted to the power used by the appliance.
In general, the use of adapters or extension leads is not advisable; if this is necessary, they must be in
accordance with the safety regulations and their amperage capacity must not be less than the maximum
for the appliance.
Before each usage, check that the appliance is in good condition and that the power cord is not
damaged: if in doubt, check with a professional, qualified technician.
The mains socket must be easily accessible in order to disconnect the appliance with ease in case of
emergency.
Position the appliance away from:
- sources of heat (e.g. open flames, gas ovens, etc.)
- deposits of liquids (e.g. sinks, etc.) to avoid falling into or splashing with water (minimum distance 2
metres).
- fabrics (curtains, etc.) or loose materials, which may obstruct the ventilation grille; in addition, check
that the front part is free of volatile materials (dust, etc.).
The supporting surface must be stable, flat and even (so that the appliance does not tip over).