Zelmer Roto VC1001, Инструкция по эксплуатации

Страница: 34 / 38

40
VC1001-001_v01
2 Press the on/off switch (4) to stop the vacuum cleaner.
Remove the plug of the cord from the socket.
3 Press both of the side buttons situated on the end of the
hose, and remove the end of the hose from the inlet of the
vacuum cleaner.
4 Release the fastening of the upper cover ( 6) , and open it.
5
Close the opening of the bag by means of a stopper.
6 Bend back the bag handle in the direction of the vacuum
cleaner handle (7) .
7
Grab the bag plate, pull it out of the handle, and then
remove the entire bag upwards.
8 The SAFBAG number is placed on a label situated in the
chamber of the vacuum cleaner.
9 Place the bag plate of a new bag into the guides of the
SAFBAG handle, and slide it to the limit. The direction in
which you should install the bag is marked by an arrow on
the bag.
10 Bend back the bag handle in the direction of the control
knob (4) .
11
Close the cover by pressing it, until you hear
a characteristic “click” – be careful not to trap the bag.
Do not start vacuuming without the SAFBAG-
type bag. No SAFBAG-type bag makes it
impossible to lock the upper cover of the
vacuum cleaner.
Zelmer vacuum cleaners are equipped with SAFBAG­type
bags in the amount given in the table. You have to replace
the bag, if:
a) the full bag indicator is on,
b) the vacuum cleaner works less efficiently,
c) the bag is full.
(De)installing the HEPA inlet filter and the
foam rubber
Before replacing the HEPA inlet filter and the foam rubber,
make sure the vacuum cleaner is turned off, and the plug of
the cord is out of the electrical socket.
INTAKE FILTER (HEPA)
The vacuum cleaners are equipped with a High Efficiency
Particulate Air (HEPA) H11­class inlet filter. A HEPA filter
is produced of special fibers, capable to high­efficiency
filtration, stopping almost all particles larger than 0.3 μm.
H11 is a class which determines the permeability of the filter.
The H11­class HEPA filter stops 95.5% of particles larger
than 0.3 μm.
1 Release the fastening of the upper cover (6) , and open it.
2 Remove the SAFBAG­type bag (13) from the chamber of
the vacuum cleaner.
3 Pull out the HEPA intake (11) from the guides situated at
the back wall of the chamber of the vacuum cleaner.
4 Put the new filter into the guides situated at the back wall
of the chamber of the vacuum cleaner.
D
Always replace a damaged HEPA intake filter
(11) with a brand new, original one. The HEPA
intake filter is guaranteed to make the vacuum
cleaner to work efficiently for ca. a year.
5
Place the SAFBAG­type bag into the chamber of the
vacuum cleaner.
6 Close the cover by pressing it, until you hear
a characteristic “click”.
FOAM RUBBER COVER
1 Release the fastening of the upper cover (6) , and open it.
2 Remove the foam rubber cover (12) from the three
fastenings of the upper cover.
3 Replace the old foam rubber cover with a new one (12)
in such a way that the three incisions on the foam rubber
cover find the three fastenings of the upper cover.
Always replace a damaged foam rubber cover
(12) with a brand new, original one.
4 Close the cover by pressing it, until you hear
a characteristic “click.”
After-work procedures, cleaning and
maintenance
1 Press the on/off switch (4) to stop the vacuum cleaner.
2 Remove the plug of the cord from the socket.
3
Wind the cord by pressing the cord winder button (3) .
Hold the cord when doing it to avoid tangling the cord up or
letting the plug hit the vacuum cleaner.
4 Disconnect the telescopic pipe from the nozzle or brush.
5 Disconnect the telescopic tube from the hose. In order to
remove the tube from the hose handle press the “A” locking
device and pull the tube in the direction of the arrow.
6 Press both of the side buttons situated on the end of the
hose, and remove the end of the hose from the inlet of the
vacuum cleaner.
7
The vacuum cleaner together with its attached
accessories may be stored in a vertical or horizontal position.
In order to this, place the hook of the nozzle brush into the
fastening for the nozzle brush. The hose may stay attached
to the vacuum cleaner as long as it is not bent too much
during storage.
8 If necessary, clean the casing and the chamber of the
vacuum cleaner with a damp cloth (it may be damped in
dishwashing liquid), dry it off, and wipe it dry.
Do not use any scrubbing agents or solvents.
E
F