Zelmer 17Z010, Руководство по обслуживанию

Страница: 14 / 16

14
thermostat 20 to the body assembly 22 , and remove the neon bracket 19 . Remove
remaining two screws 34 and the thermostat 20 .
Disassembly of the power base assembly:
Remove two screws 31 with a Philips screwdriver and remove the screw 36 with a
spanner head screwdriver and disconnect the power base 24 from the base cover 29 .
Remove two screws 30 with a Philips screwdriver, remove the clamp 26 and take out the
power cord assy 28 with the socket 27 . Disconnect the connectors of the power cord 28
from the socket 27 . Remove three rubber feet 25 from the power base 24 .
Disassembly of the kettle, type 17Z011
Disassembly of the kettle body:
Disassembly should be carried out on a table covered with a clean soft cloth,
taking care not to scratch the parts made of plastic. Remove the kettle from the power
base. Open the lid to its vertical position. Remove four screws
5 with a Philips
screwdriver. Remove the lid 1 from the lid cover 4 and take out the lid lock 2 and the lid
spring 3 . With a Philips screwdriver, remove two screws 6 mounting the handle cover 8
to the body assembly 32 . Lever up the handle cover 8 with a flat screwdriver. Put your
fingers into the resulting gap and firmly pull the handle cover 8 bringing the catches of
the handle cover 8 to be disconnected from the handle 9 . Remove the lid cover 4 from
the handle cover 8 . Remove the screw 13 with a Philips screwdriver and two screws 6
mounting the handle 9 to the body assembly 32 . Grasp the handle 9 with your hand; pull
it firmly bringing it to be disconnected from the body assembly 32 . Remove the handle
lock 7 from the inside of the body assembly 32 . Take out the water gauge assembly 11
from the silicone rings 10 located in the body assembly 32 . Squeeze the silicone ring 10
with your fingers and push it in inside the body assembly 32 . Proceed the same way with
the second silicone ring 10 , and next, remove these two silicone rings 10 from the body
assembly 32 . Hold the filter 33 with your fingers, from the inside of the body. Bend out
the catch located at the top of the filter 33 with a flat screwdriver and remove the filter 33
from the body assembly 32 . Remove three screws 22 with a Philips screwdriver and take
out the body base 18 with the switch 20 , the link 19 and the lamp cover 21 attached.
Holding the body base 18 with one hand, pull out the switch 20 , with the other hand, to
remove it from the link 19 . Squeeze the link 19 with your fingers bringing it to be
disconnected from the socket of the body base 18 . Bend out two catches of the lamp
cover 21 and remove it from the body base 18 . Undo the clamp and remove the lamp
from the neon bracket 17 . Disconnect wire connectors of the heating element from the
thermostat 15 . With a Philips screwdriver, remove the screw 16 , mounting the neon
bracket 17 and the thermostat 15 to the body assembly 32 , and remove the neon
bracket 17 . Remove remaining two screws 16 and the thermostat 15 .
Disassembly of the power base assembly:
Remove two screws 35 with a Philips screwdriver and remove the screw 27 with a
spanner head screwdriver and disconnect the power base 24 from the base cover 26 .
Remove two screws 35 with a Philips screwdriver, remove the clamp 29 and take out the
power cord 28 with the socket 23 . Disconnect the connectors of the power cord 28 from
the socket 23 . Remove three rubber feet 25 from the power base 24 .
Disassembly of the kettle, type 17Z012
Disassembly of the kettle body:
Disassembly should be carried out on a table covered with a clean soft cloth, taking care
not to scratch the parts made of plastic. Remove the kettle from the power base. Turn