background image

 
 

 
 

 

Microscope Illuminator 

Start-up 

 

HBO 50 

Inserting and replacing the burner  

Carl Zeiss 

 

 

M60-2-0014  e    05/2012 

11  

3

 

Start-up 

3.1

 

Inserting and replacing the 
burner 

 

 

1   Lamp housing 
2   Unlatching key 

3   Burner 
4   Lamp mount 

5   Spring lever (lamp mount) 
6   Spring lever ( cooling element) 

7   Lock screw of compartment 

Fig. 3 

Replacing the HBO 50 burner 

 

 

 

 

 

 

Before inserting the burner, make sure the 
equipment has been 

disconnected

 from 

line power. 

 

Replace the burner only if it has cooled 

down; let microscope illuminator cool down 

for at least 20min, otherwise there is the 

risk of burns and explosion!

 

 

Carefully tighten all respective fastening 

elements; non-compliance may result in 

contacting faults due to strong heat 
development in use. 

 

Not remove or damage the cable for the 

cooling element. 

 

Avoid fingerprints on glass components of 

the burner, if necessary remove them 
immediately. 

 

Dispose of used burner in accordance with 

the legal dispositions. Observe the 

producer’s notes (

see chapter 1.7 – Notes 

concerning the disposal)!

 

Procedure: 

 

Switch off lamp power supply. 

 

Disconnect power plug of microscope 

illuminator from lamp power supply. 

 

Let microscope illuminator cool down for at 

least 20 min. 

 

Put on face shield and protective gloves. 

 

If necessary, remove microscope illuminator 

from microscope stand. 

 

Loosen lock screw of compartment (3/

7

) for 

lamp carrier using ball-headed screwdriver 
SW 3. 

 

Press unlatching key (3/

2

) of HBO 50 down. 

Remove lamp compartment completely 
from lamp housing (3/

1

) and put it 

separately on the table. 

Содержание 423003-9000

















Отзывы: