background image

15

Water system 
balancing

A complete knowledge of the 
hydronic system, including its 
components and controls, is 
essential to proper water system 
balancing and should only be 
completed by a qualified expert. The 
system must be complete, and all 
components must be in operating 
condition before beginning the water 
system balancing procedures.

Each hydronic system has different 
operating conditions depending on 
the devices and controls installed for 
the particular application. The actual 
balancing technique may vary from 
one system to another.

After the proper system operation 
is established, the appropriate 
operating conditions such as 
water temperatures, flow rates and 
pressure drops should be recorded 
for future reference.

Before and during water system 
balancing, conditions may exist due 
to incorrect system pressures which 
may result in noticeable water noise 
or undesired valve operation. After 
the entire system is balanced, these 
conditions will not exist on properly 
designed systems. If any of these 
conditions persist, recheck the 
system for air that may not have been 
properly vented during start-up.

Water treatment

Proper water treatment is 
a specialized industry and 
therefore it is recommended 
to consult an expert in this 
field to analyze the water for 
compliance with the water 
quality parameters listed below 
and to specify the appropriate 
water treatment program. The 
expert may recommend rust 
inhibitors, scaling preventative, 
antimicrobial growth agents or 
algae preventatives. Anti-freeze 
solutions, glycols, may also be 
used to lower the freezing point.

Water content

Required concentration

Sulphate

< 200 ppm

pH

7.0 – 8.5

Chlorides

< 200 ppm

Nitrate

< 100 ppm

Iron

< 4.5 mg/L

Ammonia

< 2.0 mg/L

Manganese

< 0.1 mg/L

Dissolved solids

< 1000 mg/L

Calcium carbonate hardness

300 – 500 ppm

Calcium carbonate alkalinity

300 – 500 ppm

Particulate quantity

< 10 ppm

Particulate size

800 micron max

All Zehnder Rittling water coils 
are constructed of copper tubes 
and brass headers. It is the end 
user’s responsibility to ensure 
that any of the water delivery 
components are compatible with 
the treated water.

Failure to provide proper water 
quality will void the fan coil unit’s 
warranty.

Water system balancing and treatment

Содержание SL





















Отзывы: