zBoost
®
YX560SL User Guide
4
zBoost
®
YX560SL User Guide
5
IMPORTANT: Before Installing, Please Note These Important Factors in
Determining Performance
•
At least 15 vertical feet is needed between the Signal Antenna (receives the outside signal)
and the Base Unit Antenna (rebroadcasts the signal indoors). Separation less than 15 vertical
feet will result in decreased performance. See illustration below.
•
Keep the Signal Antenna at least 3 feet above any metal.
FIRST: Mount the Signal Antenna
Choosing the best location for the Signal Antenna provides the best performance and the largest
area of improved signal. Choose a location for the Signal Antenna using your cell phone to
determine the area of strongest signal - typically found outside, above the roofline or in an attic.
Keep in mind that if your best signal is one bar, your coverage will be limited to one small room.
Maximum performance will be achieved when the antenna is aimed at the strongest signal from
your wireless provider. If you know the direction of your provider’s tower, simply point the antenna
in that direction. If you are unsure of the location of the nearest tower, loosely secure the antenna
to the mounting surface or mast (not provided) to allow adjustment or rotation around mast. Before
securing antenna hardware, take care in finding the optimum angle at which to aim the antenna –
See
Antenna Aiming
section on page 7 for further instruction.
Once you have determined the optimum location and angle, connect the L-bracket to the antenna
and secure the antenna bracket to a mast (not provided) or a flat surface using the provided
antenna hardware.(see bracket assembly illustration). Ensure that
the antenna remains at least 3 feet above any metal objects (such as
pipes, metal siding, A/C unit etc.) and parallel to the ground with the
two holes on the side of the antenna are facing down.
► To mount antenna to a pole: Attach bracket end of antenna
to pole bracket as pictured. Use U-Bolt to secure bracket to pole
and fasten.
► To mount antenna to a flat surface: Attach bracket end of
antenna desired surface. Secure bracket using provided screws.
The of the U-Bolt is not necessary for this option.
Note
The zBoost YX560SL base unit MUST only be used
with the provided power adaptor. Use of other power
adaptors will void the warranty and may damage the
unit. Use of other equipment is not FCC approved.
15’ of vertical
separation
15’ of vertical
separation
15’ of vertical
separation
Coax Cable
Exterior Wall
Setting Up Your zBoost Signal Booster
Additional Cable Requirements
If the distance between the Signal Antenna and the Base Unit exceeds 50 feet, extension cables
are available on our website or at many home improvement and electronic stores. The included
cable is RG-6.
Please note: Cable longer than 65 feet is not recommended unless upgraded to RG-11. Maximum
recommended cable length of RG-11 is 120 feet. (see page iv) is used. A longer cable is helpful only
if it allows you to place the Signal Antenna in a location where you measure stronger signal.
Grounding the Signal Antenna
If you decide to place the Signal Antenna outdoors, it must be properly grounded. (See page iv for a
recommended grounding kit).
The set up must be in accordance with Article 810 of the National Electric Code (NEC). A listed
antenna discharge unit must be provided for the lead-in coaxial cable per NEC article 8.10.20 or the
shield of the coaxial cable must be permanently and effectively grounded in accordance with NEC
article 8.10.21. Please consult a professional installer or electrician for more information.
Securing Cable with a Drip Loop
If the Signal Antenna is placed outdoors, create a drip loop
with the coaxial cable at the point where the cable enters the
building through an outside wall. This can be done by twisting
and securing the cable into a loop (no less than 4” across)
near the entry point. This will help prevent moisture from
gathering at entry point and leaking into the building. Consult a
professional installer if you need more information.
Power Requirements
The Base Unit can be plugged into a standard 2 or 3 prong 110 VAC receptacle using the included
power supply. The power supply consumes less than 10W (less than 0.2A). For more information on
power consumption, see “Technical Specifications” on page 10.
Warning
Avoid placing the Signal Antenna near metal such as
wiring, A/C ducts, metal siding, truss plates, etc.
When connecting the cable to the antenna, run the
cable straight down from the antenna. Avoid draping
the coax near the antenna.
