6. Select the temperature
Choose the temperature which corresponds to the chosen
programme, with the help or the indications of the pro-
gramme table, according to the fibers and the fastness of
the colours.
7. Select the programme
Choose the programme according to the nature and the
degree of soil of the laundry.
Turn the programme selector clockwise to select the
chosen programme.
Never turn the timer knob when the washing machine
is working.
8. Starting of programme
The ON/OFF pushbutton "
" enables to switch on your
machine. The control lamp lights on and the programme
begins.
9. At the end of the programme.
When the selected programme is over, the machine stops
automatically. The timer knob stops on the position "I" for
the cotton programmes. The synthetic programmes end
by a rinse hold. You can finish these programmes by a
spinning (prog. 6) or a drain (prog. 14). Depress the on/off
pushbutton "
" before doing your choice.
Be careful : a safety device enables to open the lid of your
waschine machine only about 90 seconds after the ma-
chine has stopped.
After each wash:
depress the on/off pushbutton ; the control lamp lights
off.
press out the pushbutton if necessary
unplug the machine from the wall socket
turn off the water tap.
Operating instructions
1. Place the laundry in the drum
lift up the lid of the machine
open the drum with your two
hands by pressing the button
A and the two flapdoors till
they disengage
introduce the laundry into
the drum ; close the drum and
the lid of the machine
Be careful : before closing the lid of your machine, make
sure that the drum flapdoors are correctly closed :
- the two flapdoors fastened
- the button A pressed out.
2. Measure out the detergent
Measure out the amount of
detergent recommended by the
manufacturer in the main wash
compartment (
).
If you wish to carry out a
prewash, pour the amount
required into the prewash
compartment (
).
Do not exceed the MAX level.
If you wish to use liquid detergent :
choose a programme without prewash
put the measuring ball directly into the drum.
3. Add the bleach agent
You may use a bleach agent in all the washing program-
mes. However, make sure that the fabric withstands the
treatment. Bleach is automatically washed down into the
drum. Pour 1/4 to 1 glass of 12° chl bleach into compartment
marked before switching the machine on.
Make sure that the level of the liquid never exceeds the
MAX level.
4. Add the fabric softener
Pour the softener, if required, into the compartment marked
. Do not exceed the MAX level.
5. Press the half load pushbutton "
" if required.
10
Fig 6
3
INSTALLATION
A
If you want to keep the
alignment of your appliance
with the adjacent cupboards,
you have the possibility to cut
the crossbar holding the
hoses located at the back of
your washing machine (fig.6).
Water connection
Water inlet hose :
Connect the water inlet hose
to a cold water tap with a 3/4"
gas threaded orifice, after
having inserted the rugger
sealing washer with
incorporated filter (supplied
with the machine) into the
hose collar. If the water
connection is made onto new
pipes or onto pipes which have
not been used for a long time, it is advisable to run off a
certain amount of water before connecting the machine.
This will avoid foreign matter blocking the filter placed at
the end of the water inlet hose.
Water outlet hose :
Place the curved end of the outlet hose into a drain pipe
having a height between 70 and 100 cm from floor level or
secure it to a sink or bath tub. Make sure that the drain
hose is firmly secured so that it will not slip out or fall down
from its position.
The water should drain freely and, consequently, the drain
hose should not be choked or placed in such a way as to
obstruct the normal water flow. If an extension hose is
required, remember that it might cause a malfunction in
the drain pump, particularly if the extension has a length
in excess of 1 meter or if the diameter of the extension is
smaller than the diameter of the original drain hose.
Fig 1
Fig 2
Fig 5
D
Fig 6
A
B
C
Fig 4
Fig 3
Unpacking
The parts protecting the inner components of the
machine during transit are red. They must all be
removed before using your machine for the first time.
These parts and their securing means should be kept
in case the machine has to be transported again.
1. Unpack the appliance. Open the lid of the appliance and
remove the polystyrene wedge which blocks the drum.
Close the lid (fig.1).
2. Tip the appliance backwards (fig.2).
3. Remove the 2 screws (A) with red washers on the base
of the washing machine with a spanner then take out the
part (B) situated inside the appliance (fig.3).
4. Stand the appliance upright again. On the back part and
with the spanner, remove the two red loosened spacers
(C) (fig.4).
5. The holes which are now visible must be closed with the
plugs (D) provided with the appliance (fig. 5).
6. Please ensure that these parts have been removed from
the machine and keep them in case of next transport
(fig.6).
Be careful : when the machine is installed on carpeted
floor, ensure that the carpet do not obstruct the openings,
located at the base of the machine, which are provided for
ventilation.