Zanussi Electrolux ZEBF 336, Инструкция пользователя

Страница: 4 / 20

4
OPERATION
Before using
Remove all securing tapes. Wash inside the
appliance with lukewarm water and bicarbonate of
soda (5 ml to 0.5 litre of water).
Do not use soap or detergent as the smell may
linger. Dry thoroughly.
Control panel
A B C D E F G
A - Alarm light - Red
B - Fast freeze light - Amber
C - Fast freeze switch
D - Freezer Pilot light - Green
E - Freezer Thermostat control knob
F - Fridge Pilot light - Green
G - Fridge Thermostat control knob
Control Panel
A. Alarm light
If the alarm light (A) illuminates, it indicates that the
temperature within the freezer has reached a level
where safe food storage is no longer ensured.
When the freezer is first switched on, the alarm light
will stay on until the temperature has dropped to a
safe level for the storage of frozen food.
B. Fast freeze light
The fast freeze light is illuminated, to show that the
fast freeze function is working.
C. Fast freeze control switch
When you place fresh food in the appliance, press
the fast freeze control switch.
D. Pilot light
The operation light is illuminated continuously, to
show that the appliance is on.
E. Thermostat control knob
Turn the thermostat control knob clockwise to
required setting.
Start your appliance
Allow the appliance to stand for 2 hours after
installation.
Insert the plug into the wall socket. The pilot light (D)
will illuminate to show that the appliance is on.
Turn the thermostat control (G) to a midway setting.
The pilot light (F) will illuminate. Leave the appliance
for approximately 4 hours for the correct temperature
to be reached before placing food inside.
To switch off the appliance turn the thermostat
control to position “O” .
Temperature control
The temperature within the freezer is controlled by
the thermostat situated at the top of the cabinet.
To operate the freezer proceed as follows:
Turn the thermostat control knob beyond the «O»
position.
When you first start the freezer, we suggest that you
turn the thermostat control to a medium setting. For
easier turning of this control, use a small coin.The
internal temperature of the freezer is automatically
adjusted by the thermostat to ensure safe food
storage.
However, if the appliance is working in unfavourable
room conditions such as
- poor ventilation,
- high temperature,
17
G
H
F
D
PR18
F
F
F
E
E
Printed on recycled paper
Door reversal directions
1. Disconnect from the electricity supply.
2. Gently lay the fridge/freezer on its back with the
top held away from the floor by 5-8 cm (2-3
inches) of packing;
3. Remove the ventilation grill (D).
4. remove the bottom hinge (E) by unscrewing its
fixing screws;
5. Remove the freezer door by releasing it from the
middle hinge (H).
6. Unscrew the middle hinge.
7. Remove the fridge door by releasing it from the
top hinge pin (G).
8. Remove the pin then mount these on the side,
after having removed the small plugs which
should then be fitted on the opposite side.
9. reassemble the door;
10. using a 10 mm spanner, unscrew the hinge pin
(E) and reassemble it on the opposite side of the
hinge;
11.Refit the fridge door and replace the middle hinge
to the left hand side.
12.reassemble the lower hinge (E) on the opposite
side, using the screws previously removed. Slide
the hole cover (F) out of the ventilation grille (D)
by pushing it in the direction of the arrow and
reassemble it on the opposite side;
13.refit the ventilation grille (D), clipping it into place;
The doors can be aligned by adjusting the middle
hinge.
The middle hinge can be adjusted horizontally, after
having slackened the two screws with a screwdriver.
Important
After completion of the door reversing operation,
check that the door gasket adheres to the cabinet. If
the ambient temperature is cold (i.e. in Winter), the
gasket may not fit perfectly to the cabinet. In that
case, wait for the natural fitting of the gasket or
accelerate this process by heating up the part
involved with a normal hairdryer on a low setting.
D419