FOUR-CHANNEL RECEIVER ROM-24
OPERATION MANUAL
ZAMEL
Sp. z o.o.
ul. Zielona 27, 43-200 Pszczyna, Poland
tel. +48 (32) 210 46 65, fax +48 (32) 210 80 04
www.zamel.com
, e-mail: [email protected]
plik: ROM-24_inst_ext_gb | modyfikacja: 30.05.2018
The symbol means selective
collecting of electrical and electronic
equipment. It is forbidden to put the
used equipment together with other
waste.
Zamel Sp. z o.o. hereby declares that the
ROM-24 radio equipment type conforms
to Directive 2014/53/EU.
APPEARANCE
FEATURES
TECHNICAL DATA
DESCRIPTION
● Rated supply voltage 230 VAC
● Compatible with EXTA LIFE system control-
ler and transmitters
● With 4 output channels (4 x potential-free
NO contacts)
● Two-way transmission with an indication of
each output status in the application
● Programmable output status after supply
voltage loss,
● 4 programmable external inputs
● For connecting monostable or bistable con-
nectors
● 4 operating modes when working with trans-
mitters (activate/deactivate, bistable, mon-
ostable, time),
● 2 operating modes when working with a
controller (activate/deactivate, time),
● Independently programmable time for radio
transmitters, external inputs and for control-
ler,
● Times assigned independently for each out-
put
● Software can be updated remotely
The ROM-24 modular radio receiver is the
final element of the EXTA LIFE system which
allows individual control of any four devices/
circuits. Outputs take the form of four relays
with normally open terminals with maximum
load rating at 5 A. This enables the control of
low voltage circuits (for example 12/24 VAC/
VDC) and high-voltage circuits (230 VAC). The
receiver is good for remote actuation of other
devices. You can also use it for feeding control
signals. The ROM-24 receiver is also suitable
for controlling solenoids in heating systems.
Based on duplex communication between the
controller and receivers, the mobile applica-
tion always shows the current status of the
receiver. This communication method enables
the operator to change the specific parameters
of the receiver and add receivers remotely (i.e.
without actual access to the receiver). Thanks
to the frame encryption algorithm implemented
control safety is guaranteed. The ROM-24 in-
stalled outside a controller may be controlled in
parallel using the EXTA LIFE system’s transmit-
ters. You can register more transmitters with
a receiver to enable independent control from
several locations. Additional configurable cable
inputs increase the functionality of the control.
The receiver has a built-in remote software up-
date from a controller. The product is designed
for installing in switchgears using a TH35 (DIN)
bar. With removable antenna to enable the con-
nection of an external antenna.
Rated supply voltage 230 VAC
Rated frequency 50 / 60 Hz
Rated power consumption 0.65 W – standby
2.2 W – all channels activate
Transmission RF – ISM 868 MHz (868.50 MHz) band
Transmission mode duplex – 9600 bps
Maximum power 14 dBm (25 mW)
Encryption 128-bit key algorithm
Operating range max. 300 m in open areas
Transmitting/programming signalling Yes - green LED (STATUS)
Selected channel / channel status signalling Yes - red LEDs (CH1, CH2, CH3, CH4)
Maximum number of paired buttons 96 pairs (distributed into 4 channels)
Current channel status information Yes - in EXTA LIFE mobile application
Operation modes in co-operation with EXTA LIFE
system transmitters Turn on/off, bistable, monostable, time
Operation modes in co-operation with an EXTA
LIFE controller Turn on, off, timer
Number of external outputs 4
Compatible connectors* monostable (buttons), bistable
Operation modes for external inputs** Turn on/off, bistable, monostable, time
Time setpoint range*** 1 s–18 h
Number of output channels 4
Relay contact parameters 4 x NO 10A / 250 VAC (voltage-free closing
contacts)
Maximum outputs current-carrying capacity 4 x 5A / 250 VAC
Number of termination points 12 (conductor cross-section up to 2.5 mm2)
Enclosure mounting TH35 bar (DIN)
Operating temperature range -10 to +55°C
Enclosure protection rating IP20
Dimensions 90 x 35 x 66 mm (double module)
Weight 0.125 kg
* selection of switch possible only from the mobile app coupled with EFC-01 controller
** input operating mode selection depends on the type of connector type selected
*** times are assigned independently to each channel of the receiver. The periods are programmed separately for but-
tons operating in time mode, external inputs and for control from the app level
Transmit/receive signalling
/ status during programming operations
PROG. button - programming
Diodes for signalling currently selected
channel during programming / channel status
during normal operation
Antenna socket
Common terminal for channel 1 and 2
Common terminal for channel 3 and 4
Input terminals for cable control (by default
works with monostable connectors)
Output terminals (channel 1-4)
Power terminals
