230 V AC
14 V DC
-
CAUTION ! The device is designed for single-phase installation and must be installed
in accordance with standards valid in a particular country. Installation, connection
and control should be carried out by a qualified electrician staff, who act in accord-
ance with the service manual and the device functions.
1. Disconnect power supply by the phase fuse, the circuit-breaker or the switch- disconnec-
tor combined to the proper circuit.
2. Check if there is no voltage on connection cables by means of a measure equipment.
3. Connect the power supply to 230 V AC.
4. Connect the cables to the appropriate terminals in accordance with the diagram.
5. Mount the controller in the Ø60 junction box.
6. Switch on the power supply from the mains and check their proper functioning.
SLR-13 controller is designed to cooperate with standard LED lamps with LEDIX series
RGB diodes and other RGB products supplied with 10 ÷ 14 V DC (tapes, strips, modules
and RGB LED lamps) in the common “+” system. There is a wired control by means of any
potentiometer in 1 ÷ 10 V standard with a connector function. The light colour is fluently
selected by means of a potentiometer. The light intensity is also fluently selected (bright-
ening / dimming). The switch on/switch off function is realised by turning the potentiom-
eter to the minimum.
Features of the controller:
• wired control in cooperation with a potentiometer in 1 ÷ 10 V standard with the connec-
tor function,
• possibility to cooperate with standard LEDIX fittings with RGB diodes, other RGD LED
products supplied with 10 ÷ 14 V DC,
• realisation of the following functions: switch on / switch off, fluent light colour selection,
light intensity change,
• 3 x PWM output on the MOSFET transistor - maximum capacity of 2,5 A,
• 9-bit resolution of the PWM output enables the functions of the light colour selection
and brightening/dimming are very fluent,
• small dimensions and an easy mounting in the Ø60 junction box,
• low power consumption (0.1 W) - a device designed for a continuous operation.
Switching on is realised by means of a fluent brightening by turning the potentiometer’s
knob towards the maximum. The switching off is realised by means of fluent dimming by
turning the potentiometer’s knob towards the minimum. Brightening/dimming - turning
the potentiometer towards maximum/minimum. Adjusting the light colour: by pressing
the potentiometer’s knob 1 ÷ 10 V connected to the controller, there is a switch between the
brightening/dimming function (switching on/ switching off) and a function of a fluent light
colour selection. The colour selection is realised by turning the potentiometer. The selected
colour is remembered by the controller. CAUTION: After connecting the controller, the
light colour has to be chosen as the following step.
TECHNICAL DATA
MOUNTING
DESCRIPTION
DIAGRAM
APPEARANCE / OPERATION
Nominal supply voltage:
10 ÷ 14 V DC
Nominal power consumption:
0,1 W
Number of channels:
3
Maximum current in the channel:
2,5 A
Output control signal:
PWM 9-bit
Control:
A potentiometer in 1 ÷ 10 V standard
Functions:
Switching on/switching off
Fluent light colour selection
Brightening/dimming
Number of connection terminals:
8
Maximum cross-section of connection
cables:
do 2,5 mm
2
Ambient temperature range:
-10 ÷ +55
o
C
Mounting:
In a Ø60 junction box
Casing protection degree:
IP20
Protection class:
III
Dimensions:
47,5 x 47,5 x 20 mm
Weight:
27 g
Reference standard:
PN-EN 60669; PN-EN 61000
CAUTION! Nominal output voltage of the power supply (10÷14 V DC) and its nominal out-
put power must be adjusted for LED light source connected to the controller.
MAXIMUM CURRENT CAPACITY:
Up to 25 W for LED diode products supplied with 10 V
Up to 30 W for LED diode products supplied with 12 V
Up to 35 W for LED diode products supplied with 14 V
Example of
the RGB LEDIX
series fitting
10÷14 V DC
blue
R
green
G
red
B
+
Output terminals (RGB+)
to connect RGB products
Power supply terminals (+, -)
Terminals to connect
1 ÷ 10 V potentiometer
with the connector function
