230 V AC
14 V DC
CAUTION ! The device is designed for single-phase installation and must be installed
in accordance with standards valid in a particular country. Installation, connection
and control should be carried out by a qualified electrician staff, who act in accord-
ance with the service manual and the device functions.
1. Disconnect power supply by the phase fuse, the circuit-breaker or the switch- discon-
nector combined to the proper circuit.
2. Check if there is no voltage on connection cables by means of a special measure equip-
ment.
3. Connect the power supply to 230 V AC.
4. Connect the cables to the appropriate control terminals in accordance with the con-
nection diagram.
5. Mount the controller in the Ø60 junction box.
6. Switch on the power supply from the mains.
7. Add selected transmitters to the controller (a description is in TRANSMITTERS’ PRO-
GRAMMING section) and check their proper functioning.
SLR-11 controller is designed for cooperation with LED standard lamps with RGB LEDIX
series diodes and with other RGB products supplied with 10÷14 V DC (tapes, strips, mod-
ules and LED RGB lamps) in the circuit with common “+” potential. The control is carried
out wireless in cooperation with selected EXTA FREE system transmitters or with a dedi-
cated P-260 remote control. Depending on the transmitter the controller controls the func-
tions: switching on/ switching off, fluent change of the illumination power, selection 1 of
10 colours with factory configuration, fluent colour selection and the programs for fluent
automatic colour change (FLOATING) and step by step automatic colour change (STROBE).
The controller features:
• wireless control system for LED RGB standard fittings of the LEDIX system,
• to carry out the functions as follows: switching on/ switching off, fluent change of the lumi-
nous flux intensity, selection 1 of 10 colours with a default setting, fluent colour selection,
• programme realisation: automatic colour change (FLOATING) and step by step colour
change (STROBE),
• time for FLOATING and STROBE programmes is adjusted during 10 steps,
• cooperation with transmitters of the EXTA FREE wireless control system and with a dedi-
cated P260 remote control,
• 9-bit fast PWM outputs allow the brighting/dimming function to be very fluent,
• low power consumption in the standby mode (0.25 W) – controller is designed for continu-
ous operation.
TECHNICAL DATA
MOUNTING
DESCRIPTION
DIAGRAM
APPEARANCE
Nominal supply voltage:
10 ÷ 14 V DC
Nominal power consumption:
0,22 W
Number of channels:
3
Maximum current in the channel:
2,5 A
Controlling signal:
PWM 9-bit
Functions:
Switch on/ switch off
Selection 1 of 10 colours with factory configuration
Change of the luminous flux intensity
Fluent colour selection
– only for the P-260 remote control
Programs in operation:
Fluent automatic colour change (FLOATING)
Step by step automatic colour change (STROBE) –
only
for the P-260 remote control
Steps (FLOATING and STROBE)
10 (to 50 min.)
Control:
Selected EXTA FREE* system or P-260 transmitters
Radio transmission:
868,32 MHz
Transmission method:
One-way without confirmation
Coding:
Yes – transmission with addressing
Maximum number of transmitters:
32
Range:
Up to 230 m in the open area
Ambient temperature range:
-10 ÷ +55
o
C
Casing protection degree:
IP20
Protection class:
III
Dimensions:
47,5 x 47,5 x 20 mm
Weight:
27 g
Reference standard:
PN-EN 60669; PN-EN 61000
CAUTION! Nominal output voltage of the power supply (10÷14 V DC) and its nominal out-
put power must be adjusted for LED light source connected to the controller.
Output terminals (RGB+)
for connection with RGB products
Power supply terminals (+, -)
Optic signaling of the
controller’s operation
Programming button
MAXIMUM CURRENT CAPACITY:
Up to 25 W per channel for LED RGB products supplied with 10 V
Up to 30 W per channel for LED RGB products supplied with 12 V
Up to 35 W per channel for LED RGB products supplied with 14 V
Example of the RGB
LEDIX series fitting
blue
R
green
G
red
B
+
*
the SLR-11 controller does not cooperate with one push-button transmitters e.g. RNL-01
