Z3 Technology Z3-DME-02 Скачать руководство пользователя страница 36

Страница: 36 / 44

CONFIDENTIAL

DOC-USR-0054-02

____________________________________________________________________________________

Z3 Technology, LLC

♦

100 N. 8th St. STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

9.0

SUMMARY OF GUI OPTIONS

9.1

The System Setup Tab

Parameter

Options (default in bold)

Notes

Local IP Address

192.168.x.y

(192.168.81.07)

Sets the IP address of the Z3-DME-02.

Local Netmask

255.255.z.w (

255.255.0.0

)

Sets the netmask of the Z3-DME-02.

Default Gateway

192.168.a.b (

192.168.0.1

)

Can generally leave this as “192.168.0.1”.

Set Device Name

Can use to set name for Z3-DME-02.

Set Password

Can use to assign a password.

update device firmware

Used to load a new firmware image. See
“Making a Firmware Update” on page 32.

9.2

The User Presets Tab

Parameter

Options (default in bold)

Notes

new

Define a new configuration file. Up to 9
configurations can be created.

rename

Rename a configuration file.

delete

Delete a configuration file.

export

Export current settings to a file.

import

Load settings from a previously exported file.

Содержание Z3-DME-02













































Результаты поиска

Содержание Z3-DME-02

Отзывы:

Похожие инструкции для Z3-DME-02

Бренды по названию

Популярные бренды

Z3 Technology Z3-DME-02, Инструкция пользователя

Результаты поиска

Содержание Z3-DME-02

Отзывы:

Похожие инструкции для Z3-DME-02

Бренды по названию

Популярные бренды