Z3 Technology DM8168-MOD-35 Скачать руководство пользователя

Страница: 9 / 22

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 U.S.A.

♦

+1.402.323.0702

5.2 BOOTP Server Setup

1. Set up a BOOTP server as per instructions of the server software provider.

2. Create a directory to contain the files that will be passed on to the module and place the manufacturing

image files there.

3. Configure the BOOTP server so that it serves the u-boot-uartboot.bin file to the BOOTP client modules.

4. The IP address of the BOOTP/TFTP server must be set to 192.168.0.6, and the netmask needs to be

set to 255.255.0.0.

If the IP address of the server is different than 192.168.0.6, then a secondary IP address can be

created to accommodate the requirement, using the command

ifconfig eth0:1 192.168.0.6 netmask 255.255.0.0

5.3 Wiring setup

1. Connect a media player set-top-box “A” to the TV monitor using a HDMI cable. Configure the player to

output 1080p60 (if using Brite-View player set output to HDMI Auto) and set it to playback a video file in

a continuous loop. Do not use a Blu-Ray player as a source for the HDMI input of the APP-41.

2. Once the player is running remove the cable from the TV monitor and connect it to HDMI input 1 of the

Z3-DM8168-APP-41 board.

3. Connect a second HDMI source to the HDMI input of the TV monitor using a HDMI cable. Configure

the player to output 1080p60 (if using Brite-View player set output to HDMI Auto) and set it to playback

a video file in a continuous loop. Do not use a Blu-Ray player as a source for the HDMI input of the

APP-41.

4. Once the player is running remove the cable from the TV monitor and connect it to HDMI input 2 of the

Z3-DM8168-APP-41 board.

5. Connect the network cable to the RJ-45 jack on the Z3-DM8168-APP-41 board. It is possible to

connect the Z3 board directly to the BOOTP server if so desired. If there are switches or hubs between

the module and the server, make sure that they allow BOOTP packets through.

6. Connect a serial terminal to the serial port jack on the Z3-DM8168-APP-41.

7. Configure the terminal with 115200 bps, 8 data bits, 1 stop bit, no parity and no flow control. Since the

functional test takes advantage of ANSI escape codes, using the Teraterm terminal program is highly

recommended.

8. Apply power to the DM8168-APP-41.

Содержание DM8168-MOD-35























Результаты поиска

Содержание DM8168-MOD-35

Отзывы:

Похожие инструкции для DM8168-MOD-35

Бренды по названию

Популярные бренды

Z3 Technology DM8168-MOD-35, Руководство пользователя

Результаты поиска

Содержание DM8168-MOD-35

Отзывы:

Похожие инструкции для DM8168-MOD-35

Бренды по названию

Популярные бренды