manualshive.com logo in svg

Z GRILLS ZPG-700D3, Руководство пользователя, Страница: 19 / 28

Поделиться
Скачать
Z GRILLS ZPG-700D3 Скачать руководство пользователя страница 19

18

INITIAL FIRING INSTRUCTIONS

Please read this manual carefully and follow it step by step before starting your

Z Grills for the first time and each time the grill runs out of pellets.

1.Remove the Porcelain Grills, Grease Drain Pan and Heat Baffle from the interior of the

grill.

2.Open the Pellet Hopper Lid, make sure there are no foreign objects in the Auger and

Hopper.

3.With the Switch in the OFF(O) position, plug the power cord into a 110 Volt AC grounded

outlet.

4.Turn on your Z Grill and turn the Temperature Dial to the SMOKE position. Please check

the following things:

(WARNING: Please do not touch it!)

Confirm the Auger is turning. (Wait for 1-2 minutes.)

Hold your fingers above the Firepot to confirm the fan is blowing air through the Firepot.

The hotrod will heat up and you should be able to sense the heat coming from it. (It takes

approximately 1-2 minutes.)

You should see a temperature number displayed on your LED DISPLAY. If you see

something different displayed it is an ERROR CODE. NOTE: PLEASE SEE

TROUBLESHOOTING FOR DETAILS ON ERROR CODES.

5.Turn the Temperature Dial to SHUT DOWN CYCLE.

(Please note the draft fan will stay on for 10 minutes in this mode.)

6.Fill the Pellet Hopper with Pellets. Then turn the Temperature Dial to HIGH. It takes some

time for the Pellets to travel through the tube, when the Pellets start to drop, turn the

Temperature Dial to SHUT DOWN CYCLE. Leave grill until it shuts off automatically.

7.Turn the Temperature Dial to SMOKE. Allow the Pellets to come to full flame. Once flames

are coming out of the Firepot, turn the Temperature Dial to SHUT DOWN CYCLE and let the

grill cool down.

[We suggest that you should wrap the Grease Drain Pan with heavy-duty aluminum

foil before using because it is easy to clean.]

8.Place components back in place. Open the lid and turn the Temperature Dial to SMOKE. A

few minutes later, when you see whitish-gray smoke coming out of the grill, close the lid and

turn the Temperature Dial to any cooking setting desired.

9.Set Temperature Dial to HIGH and let grill run for 45 minutes at this setting to rid it of any

foreign matter. This step must be done before cooking any food.

10.Please preheat the grill for 10 minutes before adding food. This makes your grill heat up

faster and quickly reach your desired cooking temperature. Adding food sooner will slow

down the heating process.

ALWAYS START THE GRILL ON SMOKE SETTING WITH THE LID OPEN !

After the Pellets are ignited, you can turn the Temperature Dial to any cooking temperature

desired. Please don’t turn the Temperature Dial to SHUT DOWN CYCLE while in use.

Содержание ZPG-700D3





























Отзывы:

Нет отзывов