manualshive.com logo in svg

Z-Com ZAC-1023-5, Руководство пользователя

Поделиться
Скачать
Z-Com ZAC-1023-5 Скачать руководство пользователя страница 51

 

51 

 

 

Figure 23

 

Firmware Upgrade 

 

Click 

“

Browse

” to select the firmware file you would like to load; 

 

Click 

“

Upload

” to start the upload process; 

 

Wait a few minutes, the VAC Access Point will reboot after successful upgrade. 

 

 

Do NOT cut the power off during upgrade, otherwise the system may crash! 

 

Only official firmware issued by applicant to be used for firmware upgrade to 

continuously compliance of FCC rule. 

 

 

Backup/ Retrieve Settings 

It is strongly recommended you back up configuration information in case of something unexpected. If 

tragedy  hits  your  device,  you  may  have  an  access  to  restore  the  important  files  by  the  backup.  All 

these can be done by the local or remote computer. 

Open 

“

Configuration File

” in “

Management

” as below: 

 

Figure 24

 

Backup/Retrieve Settings 

Note: 

Содержание ZAC-1023-5



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды